SEGGER - Simon SuperModerator
- Member since Mar 20th 2024
This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.
-
SEGGER - Simon -
Replied to the thread Jscope RTT time stamp.
PostHello, Thank you for reaching out. The timestamp value in J-Scope is interpreted in microseconds (µs). To display the correct timestamps with J-Scope, you should start with a timestamp of 0 and increase it by 2000 (2ms) each time you send data. Best… -
SEGGER - Simon -
Replied to the thread How To Setting in J-Flash DualBank, J-Link.
PostHello, For the Traveo 2 family, we do not support Dual Bank mode. You could write your own Flash Loader if needed using the J-Link DSK. For more information, refer to: wiki.segger.com/J-Link_Device_Support_Kit … -
SEGGER - Simon -
Replied to the thread why jlink gdb server reponse "Unsupported CPU"?.
PostHello, You could try to read the registers one by one using the "reg" command: wiki.segger.com/J-Link_GDB_Server#reg Best regards, Simon -
SEGGER - Simon -
Replied to the thread Program external qspi flash on custom PCB using JLink.
PostHello, You can only choose out of the available pin configurations that are available the MCU and cant adjust it yourself. You can find the available pin configurations for the STM32U599 here: wiki.segger.com/ST_STM32U5#QSPI_Flash If your Pin… -
SEGGER - Simon -
Replied to the thread Loadbin with no reset.
PostHello, You can override the reset functionality by passing a JLink script file to the JLink Commander that implements the ResetTarget() function. This will ensure JLink calls your custom reset function instead of the default target reset. Here is an… -
SEGGER - Simon -
Replied to the thread OTP Program for Ti Hercules RM57L843 Processor.
PostHello, Programming the OTP of this chip is not supported by J-Link, and we do not have any plans to do so in the near future because our schedule is quite booked at this time. You may want to add support yourself with the JLink DSK using the… -
SEGGER - Simon -
Replied to the thread Jlinkis not able to read memory , Jlink Setting for CORTEX_M7.
PostHello, Could you please send us a J-Link log file of the failing scenario? How to enable: wiki.segger.com/J-Link_DLL#Enable_J-Link_Log_File The S/N you have sent is from a unit from 2019 which is out of support and warranty. We recommend to make use of… -
SEGGER - Simon -
Replied to the thread How to use the JLinkRemoteServer CL version.
PostHello, It seems like you are using just the default settings of the remote server, so no additional command line options should be needed. Could you please provide one log of the failing scenario and one of the successful one? The log can be enabled… -
SEGGER - Simon -
Replied to the thread Cannot get jlink plus compact working with a pinetime board.
PostHello, You seem to be using a version which is not up to date. Does the issue also occur with the current release version? https://www.segger.com/downloads/jlink Could you please send us a J-Link log file of the failing scenario? How to enable: … -
SEGGER - Simon -
Replied to the thread J-Link BASE - Target consumption.
PostHello, The resolution that J-Link can measure is approximately 12mA, so the measurement may vary significantly when the target consumption is below that. Best regards, Simon -
SEGGER - Simon -
Replied to the thread How to debug using J-Link edu mini along with NXP's S32DS.
PostHello, Unfortunately, we do not have experience debugging with the NXP S32 Development Studio either. Below is a link to a list of supported IDEs and instructions on how to set them up for debugging with Jlink: Supported IDEs Best regards, Simon -
SEGGER - Simon -
Replied to the thread Variables on fixed address in flash.
PostHello, I looked at your project and noticed that you are using the STM32F446ZC. The STM32F446ZC has a flash memory range from 0x8000000 to 0x803FFFF (256KB). This means that the address 0x8060000 you are trying to program is not valid. This might… -
SEGGER - Simon -
Replied to the thread JLink suppress "device is secured" popup msg.
PostHello, I apologize if I have expressed myself unclearly. SuppressGUI is an J-link Command string not an command for the J-Link Commander. However, you can execute J-link Command string in the commander with the exec command, so in your case you need… -
SEGGER - Simon -
Replied to the thread Triggering a functional reset on a NXP S32K344 through JLink Commander.
PostHello, You can change the reset strategy used by the J-Link in the J-Link Commander with SetResetType. In your case, to switch to a software reset, it should be: exec SetResetType = 6 For more information, please refer to: SetResetType J-Link Reset…