SEGGER - AlexD Administrator
- Member since Jan 12th 2021
- Last Activity
- , Reading thread [SOLVED] freeRTOS plugin column naming
This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.
-
SEGGER - AlexD -
Replied to the thread Ozone terminal unable to send CRLF.
PostHi SyamK, Which Semihosting service do you use? I assume, this is ReadC(). Is that correct? ReadC() returns a character. If you configure Ozone such that a dialog opens to enter a character, you need to enter a character and then click on the "OK"… -
SEGGER - AlexD -
Replied to the thread Reloading and programming in the background.
PostHi Rune, Ozone does not provide such a functionality and we do not see a big benefit in implementing such a feature. Ozone is a debugger and if you switch to Ozone it can be assumed that you intend debugging the firmware. For that use case Ozone behaves… -
SEGGER - AlexD -
Replied to the thread FreeRTOS aware plugin for Cortex-M33 (CM33).
PostHi Sam, the FreeRTOS plugin for Cortex M33 was not tested on the Cortex M4. So we cannot promise that everything will work as expected and intended. But feel free to share your experience here. Best regards -- AlexD -
SEGGER - AlexD -
Replied to the thread JLinkGDBServerCL connects, Ozone does not.
PostHi Glenn, this is a general setup issue which is not related to Ozone. Therefore I will move this thread to the J-Link section in this forum. The colleagues should be able to provide further support. @J-Link team: Could you please investigate what is… -
SEGGER - AlexD -
Replied to the thread JLinkGDBServerCL connects, Ozone does not.
PostHi Glenn, are you sure that both the Ozone log and the J-Link log were recorded in the same debug session, as I requested? I'm asking because in the Ozone log I see "Could not measure total IR len. TDO is constant high." but cannot find that in the… -
SEGGER - AlexD -
Replied to the thread [SOLVED] GUI issues.
PostHi fraengers, as I already stated: The behavior of the scrollbar is not perfect. Best regards -- AlexD -
SEGGER - AlexD -
Replied to the thread JLinkGDBServerCL connects, Ozone does not.
PostHi andrewsglenn, you did not provide a J-Link log. The procedure of creating a J-Link log is described in the Wiki article I provided earlier. When recording a J-Link log please also record an Ozone log since both need to be recorded during the same… -
SEGGER - AlexD -
Replied to the thread [ABANDONED] nRF9161 debugging with Ozone.
PostHi msdg, apparently the Ozone project file created by your tooling is not working correctly. So you should switch to setting up an Ozone project and maintaining that by yourself. You may use the Ozone project created by the new project wizard as a… -
SEGGER - AlexD -
Replied to the thread JLinkGDBServerCL connects, Ozone does not.
PostHi andrewsglenn, Could you please provide a J-Link Log file and an Ozone log, both being recorded during the same debug session where you reproduce the issue? Creating a J-Link log is described here: wiki.segger.com/J-Link_DLL#Enable_J-Link_Log_File,… -
SEGGER - AlexD -
Replied to the thread [ABANDONED] nRF9161 debugging with Ozone.
PostHi msdg, could you please check out the following WIKI page? wiki.segger.com/Nordic_Semiconductor_nRF91xx I understand that after creating a project with the new project wizard your target runs into an exception. This is often the case when the target… -
SEGGER - AlexD -
Replied to the thread [SOLVED] Enable SWO during Debugging Microcontroller Renesas RA6M5 (R7FA6M5BH) with Jlink Ultra+ causes debugger disconnection and microcontroller in stuck (power cycle is necessary for recovery).
PostHi pbizarri, looking into the J-Link log you provided I see that writing to the TPIU_SPPR register (and all subsequent writes to debug registers) fail. This happens in the context of enabling SWO in your target. So something goes wrong in that procedure… -
SEGGER - AlexD -
Replied to the thread [SOLVED] Enable SWO during Debugging Microcontroller Renesas RA6M5 (R7FA6M5BH) with Jlink Ultra+ causes debugger disconnection and microcontroller in stuck (power cycle is necessary for recovery).
PostHi pbizarri, this forum is not a support forum. SEGGER employees look in from time to time but in case there are more pressing topics on our desks responses may be delayed. In case you are eligible for support feel free to open a support case. Best… -
SEGGER - AlexD -
Replied to the thread [SOLVED] GUI issues.
PostHi fraengers, Thanks for your post. 1. We can reproduce that selecting data in the way you describe and subsequently copying the data into the clip board does not work as expected. We will fix that in a future release. When selecting the memory range… -
SEGGER - AlexD -
Replied to the thread [ABANDONED] nRF9161 debugging with Ozone.
PostHi, After having started Ozone via the "Debug with Ozone" button, do you save the Ozone project file or do you always discard the Ozone project when closing Ozone? Could you please try to set-up your project via the Ozone new project wizard, save the… -
SEGGER - AlexD -
Replied to the thread [SOLVED] freeRTOS plugin column naming.
PostHi fraengers, thank you for providing the reproducer. I just checked and conclude that right now we are not able to fix that inconvenience. The impact is zero anyway, since the scripts for Cortex-M4 and Cortex-M7 are identical except a comment. Please… -
SEGGER - AlexD -
Replied to the thread [SOLVED] freeRTOS plugin column naming.
PostHi Fraengers, Thank you for your suggestions regarding the column naming. I will present them in our next internal meeting where we discuss future improvements. At this point in time I cannot comment on whether this will be implemented and if yes,…