SEGGER - AlexD Administrator

Hi Fraengers, those questions are related to J-Link, not Ozone. Therefore I move this thread to the J-Link forum. Best regards -- AlexD

Hi, please raise a ticket in our support ticket system. The link can be found in my signature below. Best regards -- AlexD

Hi rals, what about writing a little script that does the flashing by means of the tooling you received with your J-Link/J-Trace and invoke that script from within your IDE? Assuming your IDE supports customizable buttons you the flashing will be…

Hi SyamK, Which Semihosting service do you use? I assume, this is ReadC(). Is that correct? ReadC() returns a character. If you configure Ozone such that a dialog opens to enter a character, you need to enter a character and then click on the "OK"…

Hi Rune, Ozone does not provide such a functionality and we do not see a big benefit in implementing such a feature. Ozone is a debugger and if you switch to Ozone it can be assumed that you intend debugging the firmware. For that use case Ozone behaves…

Hi Sam, the FreeRTOS plugin for Cortex M33 was not tested on the Cortex M4. So we cannot promise that everything will work as expected and intended. But feel free to share your experience here. Best regards -- AlexD

Hi Glenn, this is a general setup issue which is not related to Ozone. Therefore I will move this thread to the J-Link section in this forum. The colleagues should be able to provide further support. @J-Link team: Could you please investigate what is…

Hi Glenn, are you sure that both the Ozone log and the J-Link log were recorded in the same debug session, as I requested? I'm asking because in the Ozone log I see "Could not measure total IR len. TDO is constant high." but cannot find that in the…

Hi fraengers, as I already stated: The behavior of the scrollbar is not perfect. Best regards -- AlexD

Hi andrewsglenn, you did not provide a J-Link log. The procedure of creating a J-Link log is described in the Wiki article I provided earlier. When recording a J-Link log please also record an Ozone log since both need to be recorded during the same…

Hi msdg, apparently the Ozone project file created by your tooling is not working correctly. So you should switch to setting up an Ozone project and maintaining that by yourself. You may use the Ozone project created by the new project wizard as a…

Hi andrewsglenn, Could you please provide a J-Link Log file and an Ozone log, both being recorded during the same debug session where you reproduce the issue? Creating a J-Link log is described here: wiki.segger.com/J-Link_DLL#Enable_J-Link_Log_File,…

Hi msdg, could you please check out the following WIKI page? wiki.segger.com/Nordic_Semiconductor_nRF91xx I understand that after creating a project with the new project wizard your target runs into an exception. This is often the case when the target…

Hi pbizarri, looking into the J-Link log you provided I see that writing to the TPIU_SPPR register (and all subsequent writes to debug registers) fail. This happens in the context of enabling SWO in your target. So something goes wrong in that procedure…

Hi pbizarri, this forum is not a support forum. SEGGER employees look in from time to time but in case there are more pressing topics on our desks responses may be delayed. In case you are eligible for support feel free to open a support case. Best…

Hi fraengers, Thanks for your post. 1. We can reproduce that selecting data in the way you describe and subsequently copying the data into the clip board does not work as expected. We will fix that in a future release. When selecting the memory range…

Hi, After having started Ozone via the "Debug with Ozone" button, do you save the Ozone project file or do you always discard the Ozone project when closing Ozone? Could you please try to set-up your project via the Ozone new project wizard, save the…

Hi fraengers, thank you for providing the reproducer. I just checked and conclude that right now we are not able to fix that inconvenience. The impact is zero anyway, since the scripts for Cortex-M4 and Cortex-M7 are identical except a comment. Please…

Hi Fraengers, Thank you for your suggestions regarding the column naming. I will present them in our next internal meeting where we discuss future improvements. At this point in time I cannot comment on whether this will be implemented and if yes,…