New
Hello.
I use Programmer firmware: J-Link V11.
Program SEGGER J-Link Registration V8.10.
MCU SPC560B50L5 in LQFP144 case on the board, connection via JTAG.
When trying to connect, I have an error: “Unable to enable OnCE 10-bit TAP controller Failed to connect. Could not perform custom sequence.”
Please, tell me the reason for this error.
See the log file below:
Application log started
- J-Flash V8.10 (J-Flash compiled Sep 26 2024 08:34:30)
- JLinkARM.dll V8.10 (DLL compiled Sep 26 2024 08:34:01)
Reading flash device list [C:\Program Files (x86)\SEGGER\8.10\JLink_V810\ETC/JFlash/Flash.csv] ...
- List of flash devices read successfully (451 Devices)
Reading MCU device list ...
- List of MCU devices read successfully (11446 Devices)
Opening project file [C:\Users\DEN\Downloads\SPC560P50L5.jflash] ...
- Project opened successfully
No data file specified!
Failed to open data file [C:\Users\DEN\Downloads\]...
Connecting ...
- Connecting via USB to probe/ programmer device 0
- Probe/ Programmer firmware: J-Link V11 compiled Sep 24 2024 10:54:58
- Probe/ Programmer S/N: XXXXXXXX
- Device "SPC560B50" selected.
- TotalIRLen = 5, IRPrint = 0x01
- JTAG chain detection found 1 devices:
- #0 Id: 0x5AE41041, IRLen: 05, PowerPC JTAGC-TAP
- PPC JTAG (Identify): Enabling OnCE TAP controller. New IRLen = 10
- Connect failed. Resetting via Reset pin and trying again.
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- Failed to identify target. Resetting via Reset pin and trying again.
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- ERROR: PowerPC: Unable to enable OnCE 10-bit TAP controller
- Target interface speed: 1000 kHz (Auto)
- VTarget = 4.895V
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- Failed to identify target. Resetting via Reset pin and trying again.
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- Executing init sequence ...
- Executing Reset (0, 0 ms)
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- Failed to identify target. Resetting via Reset pin and trying again.
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- ERROR: Failed to connect.
Could not perform custom init sequence.
- ERROR: Connect failed
I use Programmer firmware: J-Link V11.
Program SEGGER J-Link Registration V8.10.
MCU SPC560B50L5 in LQFP144 case on the board, connection via JTAG.
When trying to connect, I have an error: “Unable to enable OnCE 10-bit TAP controller Failed to connect. Could not perform custom sequence.”
Please, tell me the reason for this error.
See the log file below:
Application log started
- J-Flash V8.10 (J-Flash compiled Sep 26 2024 08:34:30)
- JLinkARM.dll V8.10 (DLL compiled Sep 26 2024 08:34:01)
Reading flash device list [C:\Program Files (x86)\SEGGER\8.10\JLink_V810\ETC/JFlash/Flash.csv] ...
- List of flash devices read successfully (451 Devices)
Reading MCU device list ...
- List of MCU devices read successfully (11446 Devices)
Opening project file [C:\Users\DEN\Downloads\SPC560P50L5.jflash] ...
- Project opened successfully
No data file specified!
Failed to open data file [C:\Users\DEN\Downloads\]...
Connecting ...
- Connecting via USB to probe/ programmer device 0
- Probe/ Programmer firmware: J-Link V11 compiled Sep 24 2024 10:54:58
- Probe/ Programmer S/N: XXXXXXXX
- Device "SPC560B50" selected.
- TotalIRLen = 5, IRPrint = 0x01
- JTAG chain detection found 1 devices:
- #0 Id: 0x5AE41041, IRLen: 05, PowerPC JTAGC-TAP
- PPC JTAG (Identify): Enabling OnCE TAP controller. New IRLen = 10
- Connect failed. Resetting via Reset pin and trying again.
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- Failed to identify target. Resetting via Reset pin and trying again.
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- ERROR: PowerPC: Unable to enable OnCE 10-bit TAP controller
- Target interface speed: 1000 kHz (Auto)
- VTarget = 4.895V
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- Failed to identify target. Resetting via Reset pin and trying again.
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- Executing init sequence ...
- Executing Reset (0, 0 ms)
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- Failed to identify target. Resetting via Reset pin and trying again.
- TotalIRLen = ?, IRPrint = 0x..000000000000000000000000
- ERROR: Failed to connect.
Could not perform custom init sequence.
- ERROR: Connect failed