Search Results

Hello, You can specify your script file in J-Flash: wiki.segger.com/UM08003_JFlash#Use_J-Link_script_file (Works with recent Flasher Portable PLUS models, no older than 2 years.) Best regards Arne

Hello Harris, The serial number in SERIAL.TXT is a number (unsigned integer). If you want to use hyphens or other special characters, you'd need to use the "custom serial number" feature and provide a SNLIST.TXT file. Please refer to the chapter in the manual: wiki.segger.com/UM08022_Flasher#Serial_number_list_file Best regards Arne

Hello Nicola, Could you please open a support ticket for all Flasher Secure related requests? segger.com/support/technical-support/ Best regards Arne

Hello, The Infineon TriCore MCUs are supported via the Universal Flash Loader Configurator instead of J-Flash. Best regards Arne

Hello, Anything after the trailing quote is ignored, so it should work. Best regards Arne

Hello Matthew, This support case is already handled via email.

Hello, Could you please try another USB cable, USB hub, and another PC? If it still does nor work, please contact the support for further steps. segger.com/support/technical-support/

Hello Denis, Could you please create a support ticket for your case? segger.com/support/technical-support/ Best regards Arne

Hi Marianne, Did you check chapter 2.9.2 in UM08022 (Flasher User Guide)? forum.segger.com/index.php/Att…5ba8b31e08b06b39550bab063

Hello, This feature should work on the Flasher Portable PLUS and we are not aware of any problems. Could you please open a ticket for your case? segger.com/support/technical-support/

Hello Chris, We can only do what is theoretically possible. If you are interested in an individual solution for your MCU, which would at least provide some basic protection for the binary, please contact us directly. segger.com/about-us/contact-us/ (Production)

Hello Chris, Some ST devices support a secure firmware download interface. For devices without a secure firmware download interface, we use a different approach. We create a signature over a unique and unchangeable ID, so the firmware can verify that it is running on the device with exactly this ID. This will cause a signature failure on a cloned device, so the firmware can halt or react in another way. The system basically works as a clone protection.

Hello Laura, the Flasher RX is discontinued and superseded by the Flasher PRO. You can make use of our trade-in program to get a discount on the new Flasher: segger.com/purchase/trade-in-program/ Regards Arne

Hello Bjarne, could you please open a support ticket for your request? segger.com/support/technical-support/ (Product name = Flasher) Best regards Arne

Hello Marco, yes, the sequence is also important. Regards Arne

Hello Marco, these files do not have any metadata, it is just a dump of the incoming data stream. A small hint could be the file size: It must be a whole multiple of the sample block size. The sample block size would be for example 6 Bytes, if you have one 4 Byte variable and one 2 Byte variable. Without having a detailed look into the source, I'd suspect you specified something, which is not a whole multiple and that caused the crash. Is that correct? Regards Arne

Hello Philipp, the message indicates that it could not load JLinkARM.dll Probably some policies do not allow this on your PC, if J-Scope is not run as admin. You could try to copy the JLinkARM.dll to J-Scope's directory, maybe this works without admin rights, Best regards Arne

Hello Alex, the J-Flash application should allow you to enter the ID Code. By reading back the target memory, you can check which address was not programmed correctly. Regards Arne

Hello Alex, do you have a recent firmware on your Flasher ARM? For example: Source Code (5 lines) Regards Arne

Hello, which MCU are you going to program ("Renesas MCU" is very unspecific)? Which version (label on the bottom) of the Flasher ARM do you have? Regards Arne