Recent Activities
This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.
-
Eqqman -
Replied to the thread Segger Embedded Studio STM32F411 startup files doing something that prevents code execution.
PostAttached are the map files and the file compare results of the compiled code for debug and release mode. Aside from formatting the differences appear to be related to address locations, so this information didn't help us any. -
botched22 -
Replied to the thread Debug+trace connector for SiLabs EFR32BG22.
PostI can confirm the connector shown above worked for us on the BG22. You have to slow HCLK down by a factor of 8x to allow ETM enough time to keep up with the data rate from the trace. I did that with this line: Source Code (4 lines) -
gabriel-fz -
Replied to the thread How to use the JLinkRemoteServer CL version.
PostHi Simon, thanks for your support. Log when successful (using JLinkRemoteServer.exe -Log C:\dev\jl.log) Source Code (49 lines) The log with the failed attempt: Source Code (25 lines) Regards, Gabriel -
Masmiseim -
Posted the thread Some GUI issues.
ThreadHello Segger Team, just like to let you know. In the Embedded Studio editor, the small arrows next to the scrollbar are missing in dark mode: forum.segger.com/index.php/Att…77ed105573b080dfac7c017e4 You seem also to have problems with Unicode… -
RTTseemsOK -
Posted the thread RTT 50ms timeout is too short for linux container pass-through.
Thread* Running an STM32 device * JLink Ultra to Linux host machine over USB and SWD * VS Code remote dev container (docker) for my environment, cortex-debug extension in VS Code to active and use JLinkExe. So USB is tunneled inside to docker (linux to… -
SEGGER - Simon -
Replied to the thread Jscope RTT time stamp.
PostHello, Thank you for reaching out. The timestamp value in J-Scope is interpreted in microseconds (µs). To display the correct timestamps with J-Scope, you should start with a timestamp of 0 and increase it by 2000 (2ms) each time you send data. Best… -
SEGGER - Simon -
Replied to the thread How To Setting in J-Flash DualBank, J-Link.
PostHello, For the Traveo 2 family, we do not support Dual Bank mode. You could write your own Flash Loader if needed using the J-Link DSK. For more information, refer to: wiki.segger.com/J-Link_Device_Support_Kit … -
SEGGER - Simon -
Replied to the thread why jlink gdb server reponse "Unsupported CPU"?.
PostHello, You could try to read the registers one by one using the "reg" command: wiki.segger.com/J-Link_GDB_Server#reg Best regards, Simon -
SEGGER - Simon -
Replied to the thread Program external qspi flash on custom PCB using JLink.
PostHello, You can only choose out of the available pin configurations that are available the MCU and cant adjust it yourself. You can find the available pin configurations for the STM32U599 here: wiki.segger.com/ST_STM32U5#QSPI_Flash If your Pin… -
GiannisAn -
Posted the thread Program external qspi flash on custom PCB using JLink.
Thread -
SEGGER - AlexD -
Replied to the thread Debugging STM32H745.
PostHi Fraengers, those questions are related to J-Link, not Ozone. Therefore I move this thread to the J-Link forum. Best regards -- AlexD -
Eqqman -
Posted the thread Segger Embedded Studio STM32F411 startup files doing something that prevents code execution.
ThreadHello- Our project is on the STM32F411 Discovery board produced and sold by ST. We have a project that is meant to run as a stand-alone image but also can be uploaded via USB to the STM32F411 that is also running our bootloader. To enable this behavior… -
pilot8 -
Posted the thread Setup SystemView with FreeRTOS in IAR.
Thread -
tinydrop -
Replied to the thread why jlink gdb server reponse "Unsupported CPU"?.
PostI expect to watch aarch64 regs, Could you tell me which command I can use ? Thanks. -
aabadie -
Replied to the thread [SOLVED] Use GNU linker with Nordic nRF5340 build.
PostMy initial goal was to be able to boot from a secure image that afterwards jumps to another non secure image placed right after the initial secure one. My problem was that jumping to the non secure was triggering a hard fault. I also wanted to be able to… -
flyRobot -
Posted the thread --print-memory-usage linker flag not display evetytime building.
ThreadHi, I have a Andes RISC-V project using HPM6364ep. It is using gcc compiler so the memory usage window is empty. I add "--print-memory-usage " to the Additional Linker Options, the memory usage showed only once at first, then it will not show up if… -
LearningLabVIEW -
Replied to the thread [SOLVED] Running JLink through batch file does not work through LabVIEW.
PostThe solution ended up being that the source code in the .jlink file needed to contain the entire path to the bin file, not just the bin file name. -
fraengers -
Posted the thread Debugging STM32H745.
ThreadHello, I have a few questions regarding the debugging of a STM32H745 dual core controller. 1. Is simultaneous debugging of both cores fully supported/possible? It works, more or less, but I noticed some problems: e.g. sampling a variable for the… -
SEGGER - Alex -
Replied to the thread OTP Program for Ti Hercules RM57L843 Processor.
PostAs you have also contacted us in parallel via another channel, we will continue communication on that 2nd channel and close this thread here. BR Alex -
mspieth -
Replied to the thread OTP Program for Ti Hercules RM57L843 Processor.
PostThanks Simon. What is the near future and how much do you charge to expedite such a feature and when could it be delivered? Regards Mark