Recent Activities
This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.
-
SEGGER - AlexD -
Replied to the thread JLinkGDBServerCL connects, Ozone does not.
PostHi Glenn, are you sure that both the Ozone log and the J-Link log were recorded in the same debug session, as I requested? I'm asking because in the Ozone log I see "Could not measure total IR len. TDO is constant high." but cannot find that in the… -
andrewsglenn -
Replied to the thread JLinkGDBServerCL connects, Ozone does not.
PostHopefully these are the correct files. I tried using JLinkCommander to set the default log file generation but apparently I'm too stupid to run it. I've also regenerated the jdebug file from the project wizard. The only change I made was ad the log… -
pbizzarri -
Replied to the thread Enable SWO during Debugging Microcontroller Renesas RA6M5 (R7FA6M5BH) with Jlink Ultra+ causes debugger disconnection and microcontroller in stuck (power cycle is necessary for recovery).
PostGoodmorning I also open a ticket. -
SEGGER - AlexD -
Replied to the thread GUI issues.
PostHi fraengers, as I already stated: The behavior of the scrollbar is not perfect. Best regards -- AlexD -
SEGGER - AlexD -
Replied to the thread JLinkGDBServerCL connects, Ozone does not.
PostHi andrewsglenn, you did not provide a J-Link log. The procedure of creating a J-Link log is described in the Wiki article I provided earlier. When recording a J-Link log please also record an Ozone log since both need to be recorded during the same… -
jiri_d -
Posted the thread J-LInk EraseChip function stopped working ('Failed to erase chip').
ThreadHello, we have been using J-Link SDK for automated tests for years and now we started getting 'Failed to erase chip' every now and then. We run dozens of test procedures every night and we erase the chip before each test run. Most of the time the fix was… -
SEGGER - AlexD -
Replied to the thread nRF9161 debugging with Ozone.
PostHi msdg, apparently the Ozone project file created by your tooling is not working correctly. So you should switch to setting up an Ozone project and maintaining that by yourself. You may use the Ozone project created by the new project wizard as a… -
andrewsglenn -
Replied to the thread JLinkGDBServerCL connects, Ozone does not.
PostHi Alex Please find attached the log file. > I noticed that in your Ozone project file the function _SetupTarget() is never called. Is that intended? I used the defaults from the Ozone project wizard. I assumed it set things up correctly for… -
pbizzarri -
Replied to the thread Enable SWO during Debugging Microcontroller Renesas RA6M5 (R7FA6M5BH) with Jlink Ultra+ causes debugger disconnection and microcontroller in stuck (power cycle is necessary for recovery).
PostHi Alex, thanks for reply. please take in account this thread: [SOLVED] SWO during Debugging Microcontroller Renesas RA6M5 (R7FA6M5BH) in Renesas demoboard doesn't work using Jlink Ultra+ and instead works with J-Link OB-S124 embedded in demoboard… -
msdg -
Replied to the thread nRF9161 debugging with Ozone.
PostThat .jdebug file is automatically generated by Nordic toolkit for vscode and matches my first posts error message. The error was when I tried to use Ozones new project wizard. I am using bootloader. The merged.hex file consists of the bootloader and… -
SEGGER - AlexD -
Replied to the thread JLinkGDBServerCL connects, Ozone does not.
PostHi andrewsglenn, Could you please provide a J-Link Log file and an Ozone log, both being recorded during the same debug session where you reproduce the issue? Creating a J-Link log is described here: wiki.segger.com/J-Link_DLL#Enable_J-Link_Log_File,… -
fraengers -
Replied to the thread GUI issues.
Post2. see attached gif. it is this scrollbar behaviour, the jumping thumb, that makes it hard to use. I don't see how this is expected. forum.segger.com/index.php/Att…2ffcaf4d5f18d1b92c6d6d6a3 -
SEGGER - AlexD -
Replied to the thread nRF9161 debugging with Ozone.
PostHi msdg, could you please check out the following WIKI page? wiki.segger.com/Nordic_Semiconductor_nRF91xx I understand that after creating a project with the new project wizard your target runs into an exception. This is often the case when the target… -
fjouen -
Posted the thread Upload failed when Read-Mode-Write is executed.
ThreadHi, I have an issue trying to upload a code lower than the Read Modify Write threshold. In this case the new code is not loaded. It looks that Modify step is not performed. I have custom RISCV device. I'm using Jlink tools 7.96e (same issue with… -
SEGGER - AlexD -
Replied to the thread Enable SWO during Debugging Microcontroller Renesas RA6M5 (R7FA6M5BH) with Jlink Ultra+ causes debugger disconnection and microcontroller in stuck (power cycle is necessary for recovery).
PostHi pbizarri, looking into the J-Link log you provided I see that writing to the TPIU_SPPR register (and all subsequent writes to debug registers) fail. This happens in the context of enabling SWO in your target. So something goes wrong in that procedure… -
msdg -
Replied to the thread nRF9161 debugging with Ozone.
PostI tried to create project trough new project wizard. I got an Cortex-M BusFault Exception error. Cortex-M BusFault Exception. Source Code (6 lines) Console output Brainfuck Source Code (73 lines)Here is the .jdebug file which Ozone uses when using "Debug… -
SEGGER - AlexD -
Replied to the thread Enable SWO during Debugging Microcontroller Renesas RA6M5 (R7FA6M5BH) with Jlink Ultra+ causes debugger disconnection and microcontroller in stuck (power cycle is necessary for recovery).
PostHi pbizarri, this forum is not a support forum. SEGGER employees look in from time to time but in case there are more pressing topics on our desks responses may be delayed. In case you are eligible for support feel free to open a support case. Best… -
SEGGER - AlexD -
Replied to the thread GUI issues.
PostHi fraengers, Thanks for your post. 1. We can reproduce that selecting data in the way you describe and subsequently copying the data into the clip board does not work as expected. We will fix that in a future release. When selecting the memory range… -
SEGGER - AlexD -
Replied to the thread nRF9161 debugging with Ozone.
PostHi, After having started Ozone via the "Debug with Ozone" button, do you save the Ozone project file or do you always discard the Ozone project when closing Ozone? Could you please try to set-up your project via the Ozone new project wizard, save the… -
fraengers -
Posted the thread GUI issues.
ThreadHi, some issues with the GUI: 1. copying data from memory window may not work correctly: reproduce: a. right click on a variable => show data (Ctrl + T), memory in memory window is selected in gray b. right click into gray area in memory window, gray…