Recent Activities
This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.
-
SEGGER - Simon -
Replied to the thread JScope fails to find RTT block.
PostHello, I am not able to see your screenshot. Could you please try to re-upload it? Best regards, Simon -
aessayli -
Replied to the thread Issue when connecting to chain with multiple TAPs.
Postgot a response via support channel -
lenli -
Posted the thread the gnu linker bug for new version of segger.
Threaddear: now i am use the segger studio of v7.3. the gnu linker is used for cortex-m33 but this is some error like "prinops.c:(.text.libc.vfprintf_l+0x5c): undefined reference to `__SEGGER_RTL_vfprintf'". and segger linker is ok。 how to solver this… -
andrew.parlane -
Posted the thread JLink firmware and support/maintenance periods.
ThreadWe recently ran into an issue and when searching found this thread: [SOLVED] old firmware module that does not handle I/D-cache correctly All of our units that we've looked at so far have host/emu FW 2022 Sep 22 15:00, despite some of these units being… -
pbizzarri -
Replied to the thread Enable SWO during Debugging Microcontroller Renesas RA6M5 (R7FA6M5BH) with Jlink Ultra+ causes debugger disconnection and microcontroller in stuck (power cycle is necessary for recovery).
PostHi Alex Thanks for reply Attached full logs as you requested -
pbizzarri -
Replied to the thread SWO during Debugging Microcontroller Renesas RA6M5 (R7FA6M5BH) in Renesas demoboard doesn't work using Jlink Ultra+ and instead works with J-Link OB-S124 embedded in demoboard.
PostHi Alex. You are right! I used J-Link Configurator to set max SWO speed to 1MHz, and with the same scenario i saw from jlink log that now TPIU_ACPR is set to 99 (so clock prescaler 100, so from 100MHz SWO pin clock is 1MHz) and now it works!! So, my… -
aessayli -
Posted the thread Issue when connecting to chain with multiple TAPs.
ThreadHello, I have sent this as a support ticket but had no response since May 15, I will post it here again. we are trying to use the jlink debugger to debug our custom SoC. Our JTAG chain contains 2 taps: each one connected to a separate Risc-V processor.… -
Steve Sun -
Replied to the thread Can not halt m4 on AM572x evaluation module by JTrace..
PostHi, Alex Thanks very much. I will try my best to understand what you are saying and try again. Best regards, Steve Sun -
ninevoltz9 -
Replied to the thread [SOLVED] J-Trace Pro not functioning correctly over USB.
PostAlex, I sent you the serial number in a pm. -
SEGGER - Alex -
Replied to the thread [SOLVED] J-Trace Pro not functioning correctly over USB.
PostCan you please PM me the S/N of your J-Trace unit? -
SEGGER - Alex -
Replied to the thread SWO during Debugging Microcontroller Renesas RA6M5 (R7FA6M5BH) in Renesas demoboard doesn't work using Jlink Ultra+ and instead works with J-Link OB-S124 embedded in demoboard.
PostNot being able to specify the SWO speed is bad… Having it on “max possible” is OK but not being able to change that setting is a bad thing because different models have different max. speeds May be worth opening a ticket at Renesas for this because it… -
SEGGER - Alex -
Replied to the thread Can not halt m4 on AM572x evaluation module by JTrace..
PostHi Steven, I see that you have been in touch with Richard W. at TI. A very capable guy… Pretty sure he can help you out. As J-Link’s Cortex-M4 support is generally working and we are not talking about an issue with our flash algo etc. but a connect… -
pbizzarri -
Replied to the thread SWO during Debugging Microcontroller Renesas RA6M5 (R7FA6M5BH) in Renesas demoboard doesn't work using Jlink Ultra+ and instead works with J-Link OB-S124 embedded in demoboard.
PostHi Alex, thanks for reply As i said in my post, i cannot perform the same test using segger ozone due another issue (posted) Instead i did my test using renesas e2studio (eclipse based) where i have limited config options for jlink debugger I followed… -
ninevoltz9 -
Posted the thread Segger forum site appears to be blocking my IP address.
ThreadI cannot access this forum site from my business IP address, it times out. I had to resort to using the Tor browser to access the site. It's not a DNS issue, as I was trying to create a login, it blocked me and locked out the site. Our IP address is… -
ninevoltz9 -
Posted the thread [SOLVED] J-Trace Pro not functioning correctly over USB.
ThreadWhen I connect my J-Trace Pro Cortex to my Windows 10 PC, the device enumerates correctly and loads the WinUSB driver for it. It shows up as "J-Trace PRO" under "Universal Serial Bus devices" in device manager. When I open J-Link Commander I get the… -
Lef -
Replied to the thread [SOLVED] How to remove Library Paths from project's .elf file.
PostHi guys, thank you for your support. Actually I asked my colleagues and they told me that the tool they use also accepts .elf files. That is why they were able to see the paths... Ok so we will search for a tool that accepts .hex and see how it… -
VinayKumar Proddaturi -
Posted the thread TLE9893-2QKW62S SystemView high frequency event tracking.
ThreadHello Team, Setup Details Controller : TLE9893-2QKW62S Tool: SEGGER SystemView Debugger : Segger JLink Ultra+ Tool Versions SEGGER SystemView : V3.52a Configurations Controller Freq : 60 MHz Interface Speed : Tried with multile speed values (4 MHz to… -
geekbo -
Replied to the thread Text Editor: cursor doesn't align to mouse pointer.
PostHi stevec, I encountered similar things before, which may be caused by character set rendering styles. Try Tools->Options->Text Editors->Font Rendering, set this option to "Propotional" may works. Good luck! -
Steve Sun -
Replied to the thread Can not halt m4 on AM572x evaluation module by JTrace..
PostHi, Alex Thanks very much. It seems that what you said makes sense, but I'm NOT sure. What is your suggestion? I can try on my board. My board is a official board, AM572x evaluation module. ti.com/tool/TMDSEVM572X My JTrace is a official genuine…