Hi
When I try to work a JLINK +nxp lpc2124, I got this error...
the PCB Board is designed by someone others...
it can not work because of the fault.
the infomation is shown below:
SEGGER J-Link Commander V4.14f ('?' for help)
Compiled Jul 5 2010 14:21:11
DLL version V4.14f, compiled Jul 5 2010 14:21:00
Firmware: J-Link compiled Jul 30 2008 11:24:37 ARM Rev.5
Hardware: V5.90
S/N : 28010319
Feature(s) : RDI, FlashDL, FlashBP, JFlash, GDBFull
Info: TotalIRLen = 4, IRPrint = 0x01
VTarget = 3.170V
Found 1 JTAG device, Total IRLen = 4:
#0 Id: 0x4F1F0F0F, IRLen: 04, IRPrint: 0x1, ARM7TDMI-S Core
Found ARM with core Id 0x4F1F0F0F (ARM7)
ETM V1.2: 1 pairs addr.comp, 0 data comp, 4 MM decs, 1 counters
RTCK reaction time is approx. 252ns
Using adaptive clocking instead of fixed JTAG speed.
J-Link>r
Reset delay: 0 ms
Reset type NORMAL: Using RESET pin, halting CPU after Reset
Info: TotalIRLen = 4, IRPrint = 0x01
WARNING: RESET (pin 15) high, but should be low. Please check target hardware.
Info: Core does not stop after Reset, setting WP to stop it.
Info: Failed to halt CPU core after Reset (BP@0), using default reset strategy.
Info: Resetting target using RESET pin
WARNING: RESET (pin 15) high, but should be low. Please check target hardware.
WARNING: RESET (pin 15) high, but should be low. Please check target hardware.
Info: Halting CPU core
Info: Using DBGRQ to halt CPU
Info: Resetting TRST in order to halt CPU
Info: Resetting target using RESET pin
WARNING: RESET (pin 15) high, but should be low. Please check target hardware.
WARNING: RESET (pin 15) high, but should be low. Please check target hardware.
Info: Halting CPU core
Info: Using DBGRQ to halt CPU
Info: Resetting TRST in order to halt CPU
****** Error: Unable to halt ARM core
J-Link>
I can not halt or reset the MCU ,so i can not download the Application~~~
pls help me~
best regards
When I try to work a JLINK +nxp lpc2124, I got this error...
the PCB Board is designed by someone others...
it can not work because of the fault.
the infomation is shown below:
SEGGER J-Link Commander V4.14f ('?' for help)
Compiled Jul 5 2010 14:21:11
DLL version V4.14f, compiled Jul 5 2010 14:21:00
Firmware: J-Link compiled Jul 30 2008 11:24:37 ARM Rev.5
Hardware: V5.90
S/N : 28010319
Feature(s) : RDI, FlashDL, FlashBP, JFlash, GDBFull
Info: TotalIRLen = 4, IRPrint = 0x01
VTarget = 3.170V
Found 1 JTAG device, Total IRLen = 4:
#0 Id: 0x4F1F0F0F, IRLen: 04, IRPrint: 0x1, ARM7TDMI-S Core
Found ARM with core Id 0x4F1F0F0F (ARM7)
ETM V1.2: 1 pairs addr.comp, 0 data comp, 4 MM decs, 1 counters
RTCK reaction time is approx. 252ns
Using adaptive clocking instead of fixed JTAG speed.
J-Link>r
Reset delay: 0 ms
Reset type NORMAL: Using RESET pin, halting CPU after Reset
Info: TotalIRLen = 4, IRPrint = 0x01
WARNING: RESET (pin 15) high, but should be low. Please check target hardware.
Info: Core does not stop after Reset, setting WP to stop it.
Info: Failed to halt CPU core after Reset (BP@0), using default reset strategy.
Info: Resetting target using RESET pin
WARNING: RESET (pin 15) high, but should be low. Please check target hardware.
WARNING: RESET (pin 15) high, but should be low. Please check target hardware.
Info: Halting CPU core
Info: Using DBGRQ to halt CPU
Info: Resetting TRST in order to halt CPU
Info: Resetting target using RESET pin
WARNING: RESET (pin 15) high, but should be low. Please check target hardware.
WARNING: RESET (pin 15) high, but should be low. Please check target hardware.
Info: Halting CPU core
Info: Using DBGRQ to halt CPU
Info: Resetting TRST in order to halt CPU
****** Error: Unable to halt ARM core
J-Link>
I can not halt or reset the MCU ,so i can not download the Application~~~
pls help me~
best regards