Ronald Community Member

  • Member since Feb 16th 2020
Last Activity

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    Hi Michael and Arne By take a near study of the of the data I found out that I could do this. #auto patch 2…
  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    HI Michael Ok, then I can't use this option, because I got six Pathes to load for each device and according to manual only 4 is allowed. Best regards Bjarne
  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    Godmorning Michael I tried the patch way, but it didn't work. I have added Patches.txt and Serial.txt Module2 directory. Then did: #status #selmodule 2 #select 2 flasher.uni #auto 2 It did program the DUT, but did not use the patches. I can see that…
  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    Hi Arne and Michael I'm very pleased. It works now. 5V is king :) Now to the next question: My data layout is a little bit special: For every DUT i have to program, a lot of the data is different. Not only serial number. My data layout is 64 byte long…
  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    Hi Michael According to Data sheet for 24LC025 microchip, the page size is 16! See attachment. The HW setup is not write protected. See attachment The board with the EEPROM is powered up and supplying the eeprom with 5V My connection from flasher is on…
  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    Hi Arne This is programming commands and respond from Flasher: #status #ACK #STATUS:READY #selmodule 2 #ACK #SELECTED:2 #Select 2 flasher.uni #ACK #OK #auto 2 #ACK #RESULT:2:ERR255:Error while flashing #DONE Here is output from port 42:
  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    Hi According to the manual AN08007, extension is not needed: You can check if the Flasher ATE is ready to accept commands using the command #status. If yes the answer is #STATUS:READY. First, choose the project file taht shall be flashed. Use the
  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    If I do this: #select 2 flasher.uni (instead of only #select 2 flasher) It still fails, but in log file it says only: SN: 0 - Failed and the flasher ATE has produced a file more called "Serial.txt"! Regards Bjarne
  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    Hi Arne I tried #select 2 flasher instead but it didn't help. Log file says: ERROR: Failed to open flasher config file SN: 1 - Failed Is "port 42" the serial port on Flasher ATE? I don't have a serial device. Need to get one before I can do…
  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    Hi I manage to use the universal flash loader. I have downloaded to the Flasher ATE with success These files are placed at folder "module002" 6051.dat FLASHER.UNI I2CEEPRO.PEX I try flash the EEPROM (24LC512) via Telnet In telnet I do: #status =>…
  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    Thanks:) Is 24C512 the same as 24LC512 in terms of programming?
  • Ronald -

    Replied to the thread I2C programming EEprom with Flasher ATE.

    Post
    Thanks Arne The device is not at the list in Universal Flashloader App. Do I then need to make a custom flashloader? Thanks in advance Bjarne
  • Ronald -

    Posted the thread I2C programming EEprom with Flasher ATE.

    Thread
    Hi Is it possible to use Flasher ATE to program a EEProm 24LC512 from MicroChip? /Bjarne