SEGGER - Alex Administrator

  • Member since Dec 18th 2007
Last Activity

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • SEGGER - Alex -

    Replied to the thread [SOLVED] Same error.

    Post
    Old versions are available for download on the website. This thread will be closed.
  • SEGGER - Alex -

    Replied to the thread erasing and loadbin.

    Post
    Erase, without any further parameters, will erase all flalsh banks known to J-Link for the selected MCU. This means, for a MCU with 2 MB flash, it will erase 2 MB. Loadbin erases the affected ranges. Meaning if your bin file is 512 KB in size, only 512…
  • SEGGER - Alex -

    Replied to the thread JLINK plus not working with XMCFlasher.

    Post
    First you write that with XMCFlasher and J-Link PLUS you cannot even connect. Then you write that J-Link Commander connects but cannot reset, halt, … the target while XMCFlasher can. One of these statements is incorrect… Which one? Nnote that…
  • SEGGER - Alex -

    Replied to the thread Jlink log file structure.

    Post
    Hi, Log files do not have any documented structure / format. The format may change from one version to another, without further notice or even a release note entry. The way to go is checking the return value of the application, not parsing the log…
  • SEGGER - Alex -

    Replied to the thread SWD isolator power.

    Post
    Hi, You did get it wrong. You cannot power a target via SWD isolator. Actually, the SWD isolator needs to be powered by the target. It has 2 sides: Emulator / J-Link Target The Emulator side is powered by J-Link via pin 19. The target side is powered…
  • SEGGER - Alex -

    Replied to the thread JLink OB STM32F103 firmware upgrade needed.

    Post
    Hi, This is not a genuine J-Link, but an illegal clone. These are excluded from any support and must not be used with the J-Link software (see license terms) This thread will be closed and probably also deleted.
  • SEGGER - Alex -

    Replied to the thread JLink OB STM32F103 firmware upgrade needed.

    Post
    Hi, Could you please let us know which eval board you are using? (Eval Board name and vendor name) Can you please send us the serial numbers of your OBs? (Either post or PM is fine)
  • SEGGER - Alex -

    Replied to the thread J_Link cannot connect to target.

    Post
    2 things: 1) You need a EDU V10 or later: wiki.segger.com/Software_and_H…tures_Overview#J-Link_EDU 2) There is some wiring problem on your side, as even the very low-level jTAG scan seems to fail.
  • SEGGER - Alex -

    Replied to the thread No JLinkGDBServerCL console in Eclipse.

    Post
    Hi, Yes, JLinkGDBServerCL.exe is a SEGGER application. It is a command line application. If you see a window or not or if stdout is forwarded to some Eclipse window is all Eclipse / plugin specific and out of our control. This is the plugin you are…
  • SEGGER - Alex -

    Replied to the thread No JLinkGDBServerCL console in Eclipse.

    Post
    Wrong forum. Neither Eclipse nor the GDBServer plugin in Eclipse are SEGGER products. This is more a question for an Eclipse forum. BR Alex
  • SEGGER - Alex -

    Replied to the thread J-Link "Read 1 bytes @ address 0x00000000" on LPC2387.

    Post
    Hi, You are not using “GDBServer” from MinGW but “GDB. These are different applications. J-Link GDBServer works. If you are looking for a GCC toolchain (GCC, GDB, …) how about the official one from ARM?
  • SEGGER - Alex -

    Replied to the thread [SOLVED] Which adapter to use with Jlink Plus and XMC1400.

    Post
    The Tx and Rx pins yyou are referring to here are for virtual COM port. This is a USB 2 serial (UART) bridge to communicate with your target application. They have NOTHING to do with the ASC BSL of the XMC. So yes, you are mistaken. Again, the TMS /…
  • SEGGER - Alex -

    Replied to the thread [SOLVED] Which adapter to use with Jlink Plus and XMC1400.

    Post
    Hi, To the best of my knowledge, SWD and ASC share the same pins. ASC is a half-duplex UART, meaning that 1 pin is Tx and Rx. In SWD mode the pin acts as SWDIO and in ASC mode it is TxRx. On the adapters you may find it as TMS (if used on a device that…
  • SEGGER - Alex -

    Replied to the thread OMAP5912 and JTAG pniout.

    Post
    Where is the problem in buying? The schematics are not publicly available. You may be able to get some schematics / recommendations etc. on the TI website, as it is a TI MCU and TI spec.
  • SEGGER - Alex -

    Replied to the thread MY JLINK will not connect to my Nordic Thingy 91 Devices.

    Post
    Hi, The EDU you are using is a V9 one which is out of support and maintenance. It is possible that it does not support all features required to debug the nRF91. Another possibility is a bad debug connector on your board (short-circuit etc)
  • SEGGER - Alex -

    Replied to the thread Eclipse S32DS dump export array via GDB with j-link.

    Post
    Sounds like the wrong forum to me. This is not really J-Link related but more generic like “how to export from GDB to CSV”. Stackoverflow may be better suited for this kind of question. stackoverflow.com/questions/92…rmatted-like-xxd-from-gdb
  • SEGGER - Alex -

    Replied to the thread Connecting JLink OB to ARM based computer.

    Post
    Hi, Did you use the DEB installer or the tgz? In case you used the tgz, it is your job to make sure that the rules file is copied to the correct location. The Nordic OB has a different USB identification than the BASE. What does “lsusb -l” show if…
  • Hi, The lower limit for a full J-Link (BASE, PLUS, …, not! EDU Mini) is 1.2V. Can you please give this a try and post the *complete* output? wiki.segger.com/J-Link_cannot_…ty_using_J-Link_Commander BR Alex
  • SEGGER - Alex -

    Replied to the thread OMAP5912 and JTAG pniout.

    Post
    We recommend to use this adapter, so you do not have to care about the pins: segger.com/products/debug-prob…apters/14-pin-ti-adapter/
  • SEGGER - Alex -

    Replied to the thread RTT Viewer automatic connect when device powers on.

    Post
    Hi Johannes, It should not really be an issue to get your hands of the SDK. It’s a very small one-time fee, for a company-wide license of the SDK. And as you are asking for super-special stuff here, it should not be a problem to get a specialized tool…