SEGGER - Alex Administrator

Hi, The PID used depends on what features are reported on the USB level. PID 0x0105 is the default for that kit which means J-Link + VCOM + drag & drop. The 0x0101 you are seeing is most probably the bootloader of the OB because the bootloader does not…

Hi, Sorry for the delay in response on this. What you are running into is what is described as "case 9" here: wiki.segger.com/J-Link_RISC-V#JTAG_chain_auto-detection Why is that the case? Because J-Link does not know your RISC-V TAP Id, so it does not…

Hi, As you correctly pointed out, VCOM uses the USB CDC-ACM class which is USB specific and therefore not available over Ethernet. There are J-Link API functions that may be used to access the VCOM channel (of course not concurrently with a terminal…

Quote from JavierSVE: “and e2studio is just another eclipse. ” Well, I would not take that for sure. Under the hood, Renesas did a lot of stuff and initially broke things that were working in a vanilla Eclipse. So it is not necessarily just "another"…

Wrong forum to ask. This is regarding configuration of Renesas e2studio. I am not even sure if what you are trying to do is possible. I recommend to check with Renesas. By the way: If you only want to flash the micro, why firing up a whole Eclipse…

If you check the release notes, you will notice a fix for installing the DEB package under WSL2. segger.com/downloads/jlink/ReleaseNotes_JLink.html This probably has some kind of bad side effect onto installation to docker images. Do not know yet. We…

Hi, For my understanding: Are you trying to build a docker image or run an existing docker image? So far, the thread you referenced in [2] more or less clearly says it: "A Docker container doesn't have access to host devices and isn't running system…

Hi, I have something to add: While I do not see how it could happen that directories were not deep searched, I could identify a bug that caused directories above $HOME/.config/SEGGER/JLinkDevices were also searched by accident. This will be fixed in…

Hi, Without knowing your application, it is hard to say what is going on here. All I can say is that GDB sets the PC to the application and then sets 3 breakpoints in QSPI flash. After starting the core, it looks like no breakpoint none of these…

Hi, This depends on your particular MCU / device (e.g. Infienon XMC4200...), rather than only the core (e.g. ARM Cortex-M4). There are MCUs for which J-Link performs a reset as part of the connect. For example, the Infineon XMC4xxx series devices: …

Hi, Sorry for the late reply. I cannot confirm this. Just tested this under Linux Mint and the deep search is working correctly, as far as I can see: forum.segger.com/index.php/Att…e1f0d5ee4f8e16c86f7a9a514 BR Alex

This shows the minimum required pins for FINE: segger.com/products/debug-prob…adapters/rx-fine-adapter/

Hi, wiki.segger.com/RTT wiki.segger.com/J-Link_RTT_Viewer#The_Terminal_Tabs 1 buffer on target side per “channel”. n terminals may share 1 buffer. Terminals are a memory saving way of having multiple tasks doing output that should be visually…

Debugging (J-Link): No Production Programming (Flasher): In the pipe but no specific schedule yet If you are interested in production programming, I recommend to get in touch with our sales directly.

Hi, You need to be more specific regarding what connector you are measuring on. Do you have a J-Link model with the 20-pin 0.1" connector? Then 5V is output on pin 19. wiki.segger.com/UM08001_J-Link…e#20-pin_J-Link_connector If you have a model with…

Thanks for trying. So it may be related to the fixed issued but it seems not to be the root cause in your case… We will try it out here and provide some feedback.

Hi, Sounds like the register you are using to reset the chip, also resets the debug logic, which is usually not what you want because it results in - loss of hardware breakpoints being set - J-Link being unable to halt the core before potential user…

Not sure what you are trying to say / ask. The STM32F051 is a Cortex-M0 based MCU that does neither provide trace pins, nor incorporates an ETM which is needed for the “code coverage” trace feature. The code coverage feature is not available on the…

Hi, To the best of my knowledge, e2studio uses the J-Link API directly. At least we have never heard of J-Link GDB Server being used e2studio internally. It is still possible that there is a wrapper inside e2studio that uses the “e2-server-gdb.exe”…