SEGGER - Nino Administrator

  • Member since Jan 2nd 2017
Last Activity
, Reading thread Timestamp from PC

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • SEGGER - Nino -

    Replied to the thread [SOLVED] Ozone on debian buster segfault.

    Post
    Hello, Great to hear that you are up and running again. We will consider this thread as solved now. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread Ozone ETM trace limit.

    Post
    Hello, 1: No, you can use your current J-Trace PRO. It will be launched with a J-Link software release which are available for free so you just need to install the latest software when it is available. 2: Currently not possible. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread Internal flash memory erased using J-Link Commander.

    Post
    Hello, Thank you for your inquiry. If you issue a simple erase command with J-Link Commander or Embedded Studio and similar it will erase all internal Flash Banks. This includes the BootROM for this device as it is configurable. If you are debugging…
  • SEGGER - Nino -

    Replied to the thread Ozone ETM trace limit.

    Post
    Hello, Thank you for your inquiry. J-Trace PRO will currently buffer instruction trace data up to 64 MB (depending on your target device this can be more or less than 67M datapoints). We are currently working on expanding Ozone and J-Trace PRO so you…
  • SEGGER - Nino -

    Replied to the thread Jlink SDK ETM and ITM support.

    Post
    Hello, Thank you for your inquiry. Correct, different data channels would be trace pins, trace buffer and SWO. Only one can be evaluated at a time. But ETM and ITM packets can be channeled through the trace pins at the same time. This has to be…
  • SEGGER - Nino -

    Replied to the thread J-Link EDU for reading ETM of ARM Cortex-M4 series.

    Post
    Hello Giacomo, Thank you for your inquiry. That data can only be accessed with a J-Link EDU if the target device has an MTB or ETB implemented. In all other cases a J-Trace PRO would be needed to capture the ETM data that is streamed out of the trace…
  • SEGGER - Nino -

    Replied to the thread SAMA5 ETB trace.

    Post
    Hello, We tried to reproduce the issue with a SAMA5D2 XPlained Ultra but everything was working as expected with Embedded Studio and Ozone. Are you using the same board? If not which one? If you are using the same board, did you convert the EDBG to…
  • Hello, Thank you for your inquiry. The J-Link software version you are using is a couple of months old. Could you give the latest software version a try? segger.com/downloads/jlink/#J-…twareAndDocumentationPack Does that solve the issue? Best…
  • SEGGER - Nino -

    Replied to the thread Solution build not triggering project build.

    Post
    Hello, Thank you for your inquiry. With the latest Embedded Studio V4.18 you should now have the pre build option as a solution option as well. Could you give it a try? Is that what you were looking for? Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread SAMA5 ETB trace.

    Post
    Hello, I moved the inquiry to a new thread as this question is not related to the other. Both J-Links support ETB trace on the SAMA5 target device. Do you get any error message? Which version of Ozone are you using? Do you get any error messages? Best…
  • SEGGER - Nino -

    Replied to the thread Keil Cortex-M7 ETM Trace support.

    Post
    Hello, Quote from DawidS: “I know Ozone - the last version I used didn't had the ability to search in ETM Trace log which made Ozone almost useless for us ” Could you elaborate how you can do this in Keil? I just tested the latest uVision version…
  • SEGGER - Nino -

    Replied to the thread SystemView's bugs.

    Post
    Hello, Thank you for your inquiry. 1: Will be fixed in a future SystemView source release. 2: Is not reproducible with the currently available SystemView sources: segger.com/downloads/jlink/systemview_target_src Which version are you using? Quote from…
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Ozone on debian buster segfault.

    Post
    Hello, Attached you can find an example SWO project that contains an Ozone project which will output the SWO stream in Ozone terminal. Could you give that a try? I tested it with our STM32F103 Nucleo Board that we have in house and everything is working…
  • SEGGER - Nino -

    Replied to the thread How can I code for SystemView?.

    Post
    Hello, Thank you for your inquiry. Happy to see your interest in SystemView. Currently we do not offer a public repository for collaboration and there are no plans to add such an interface. So the correct approach for now would be to either post us your…
  • SEGGER - Nino -

    Replied to the thread Redefinition of FLASH in SEGGER_Flash.icf.

    Post
    Hi JLuc, Thanks for verification. This explains why the build is failing with the new version as the new Linker script is referenced now where the regions are renamed to be more consistent. By adjusting the memorymap file or memory segments settings in…
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Ozone on debian buster segfault.

    Post
    Hello, Great to hear that you are up and running again. Quote from billium: “If I can find out how I'll mark as solved. ” Don't worry I will take care of it. Quote from billium: “One point though, if I use JLinkSWOViewer I can see my…
  • SEGGER - Nino -

    Replied to the thread [SOLVED] RTX RTOS Ozone plugin develop.

    Post
    Hello, We received your inquiry vie our support system as well. To keep all information at once place this thread will be closed now. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Ozone on debian buster segfault.

    Post
    Hello, Thank you for your inquiry. The issue should be fixed with Ozone V2.62f. Could you give it a try? Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread STLink conversion utility for STLink v3.

    Post
    Hi, G4 support will be added with the next J-Link software beta planned this week. To get a notification when it is available you can subscribe here: segger.com/notification/subscribe.php?prodid=7,94 Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread JLink RTT logger for Raspberry Pi - no capture.

    Post
    Hello, Thank you for your inquiry. The J-Link software package for ARM hosts comes without support so please understand that we can't put time into this issue. Alternatively we recommend using an external PC that is connected to the Raspberry via…