SEGGER - Nino Administrator

  • Member since Jan 2nd 2017
Last Activity
, Viewing forum index

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • SEGGER - Nino -

    Replied to the thread SystemView Windows 10 cannot capture data normally.

    Post
    Hello, Thank you for your inquiry. The reported behaviour is known to us and is due to an issue with the J-Link DLL. If you use the same J-Link software version on your Ubuntu system you would see the same behaviour. Simply install the latest J-link…
  • SEGGER - Nino -

    Replied to the thread Headless Install - Nixos installation.

    Post
    Hi Phillip, The extraction process is working as expected on Nixos as well. But it appears that the setup can't launch correctly. Eventually due to some missing shared library. To verify this could you try the following? Run the installer manually and …
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Did not finish 'cmake'.

    Post
    Hello, Thank you for your inquiry. Please note that the nRF Connect software and its implementation is maintained and supported through Nordic Semiconductor. So we recommend contacting Nordic support in this regard. Best regards, Nino
  • Hello Braon, Thank you for your inquiry. Do you see the same behaviour in the latest Embedded Studio version? Please understand that we can't provide support for old Embedded Studio versions. Best regards, Nino
  • Hi, OK I see. Unfortunately this behaviour is not reproducible for us. Both window layouts maximized, and windowed are restoring correctly for me. Could you try the following? - Close Ozone - Delete the .user file from the project folder - Reopen…
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Streaming Trace over SWD?.

    Post
    Hello Pete, Thank you for your inquiry. Such mode is not supported by our software due to its extreme speed limitations in comparison to the parallel trace with 4 data lanes. It would simply constantly create overflows on target device side due to the…
  • SEGGER - Nino -

    Replied to the thread Can not Start Recording.

    Post
    Hi, Ok the settings look fine. Could you give the attached embOS project a try? It comes with SystemView instrumentation out of the box. You can find the project under \Start\BoardSupport\ST\STM32G431_STM32G431RB_Nucleo To rebuild the project our IDE…
  • Hello, Thank you for clarification. The SAMV71 uses ETMv4 for tracing where support for conditional non branch instructions is "implementation defined" so currently this is not available for this target device. That is why the IT block evaluates…
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Dark Theme For Ozone.

    Post
    Hello, Thank you for your inquiry. A dark theme is already on our todo. But we currently can't name a fixed timeschedule when it will be available due to higher priorities on other features. To get a notification with the release notes for Ozone on…
  • SEGGER - Nino -

    Replied to the thread Ozone v3.20b not stopping at main().

    Post
    Hello, Ok thank you for verifying. You can either attach the elf file here in the forum, or if the data is confidential simply open a support ticket where you attach the elf file and reference this forum post: segger.com/ticket/ Best regards, Nino
  • Hi, I just gave it a quick try with a 2k and 4k display where the 4k display is the secondary on a Win10 machine with Ozone V3.20c and everything was working as expected. Is this still reproducible for you? If yes could you provide a screenshot of the…
  • SEGGER - Nino -

    Replied to the thread Can not Start Recording.

    Post
    Hello, Thank you for your inquiry. Such an issue is not known to us. Could you provide a screenshot of the recorder settings in SystemView under Target->Recorder Configuration? Best regards, Nino
  • Hello, Thank you for your inquiry. Did you follow the suggestions in the thread you have linked? That should already provide you with all needed information to solve this issue. Why are you setting Cortex-M4 as the target device? Is your target device…
  • SEGGER - Nino -

    Replied to the thread Patches for FreerROTS V10.0.1?.

    Post
    Hello, Thank you for your inquiry. Currently we do not provide such patch file. We will put this on the wishlist for SystemView but can't promise anything at the moment as FreeRTOS is not our priority at the moment. Eventually the following threads…
  • SEGGER - Nino -

    Replied to the thread Headless Install - Nixos installation.

    Post
    Hello Phillip, As I said, Nixos is not officially supported by us so please understand that we can't put more time into this investigation. Maybe the Nixos community/support could provide you with information what would be needed here to make the…
  • SEGGER - Nino -

    Replied to the thread Abort flash download for wrong mcu type.

    Post
    Hello, Thank you for your inquiry. It is unfortunately not easily possible for the J-Link to detect what device is connected currently so the J-Link software assumes that the device name that is passed at the beginning of the debug session is…
  • SEGGER - Nino -

    Replied to the thread Example Program 'Hello World' can't stop.

    Post
    Hello, Thank you for your inquiry. The application does not stop. For printf this example uses SEGGER RTT which uses a buffer on the target as a I/O channel to J-Link. The default buffer is 1 kB in size. Depending on how fast the target device is this…
  • Hi, Thank you for your inquiry. What target device are you tracing currently? Do you see this behaviour only on IT blocks or also with other conditional instructions e.g. conditional branches? Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread [SOLVED] STM32F429ZI SWO Trace - Timestamping?.

    Post
    Hi, Great to hear that you are up and running again. We will consider this case as solved now. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread Headless Install - Nixos installation.

    Post
    Hello, Thank you for your inquiry. Such an issue is not known to us. How did you call the installer exactly? Did you do it with sudo (or whatever Nixos equivalent is)? I just gave the headless installer a try under Ubuntu LTS 19.04 and everything was…