SEGGER - Nino Administrator

  • Member since Jan 2nd 2017
Last Activity
, Viewing forum index

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • SEGGER - Nino -

    Replied to the thread Open Flashloader + interrupts.

    Post
    Hello, Quote from tdl7rt: “I mean in the FlashDevice config struct: ” In that case see here: wiki.segger.com/Open_Flashloader#SectorInfo Quote from tdl7rt: “No it does not need, but I was adapting existing ST HAL code which depends on having a…
  • SEGGER - Nino -

    Replied to the thread GDB doesn't correctly flash mx29lv160db nor flash.

    Post
    Hello, Please understand that CFi init is user responsibility and leaves our regular support scope so we can't offer assistance in this case. Generally the ConfigTargetSettings looks correct if the addresses are correct. For the target specific CFI init…
  • SEGGER - Nino -

    Replied to the thread MSP432 cannot be flashed.

    Post
    Hello, Thank you for your inquiry. Such an issue is not known to us. The UniFlash is not our software so we can't comment on it working or not. But you should be able to Flash the MSP432P4 with Segger software like J-Link Commander or J-Flash. They are…
  • SEGGER - Nino -

    Replied to the thread JFlash Cypress PSoC Protection.

    Post
    Hello, Which J-Link software version are you using when trying to unlock? With the latest version you should get a pop up asking if you want to unlock the device. Do you get an unlock pop up when using the latest J-Link software version and does…
  • SEGGER - Nino -

    Replied to the thread Open Flashloader + interrupts.

    Post
    Hi Daniel, Could you elaborate what you would need interrupts for? To our knowledge the L5 series do not need interrupts for operating the Flash controller. Quote from tdl7rt: “Another question, is there a limit on the section size? ” What exactly…
  • SEGGER - Nino -

    Replied to the thread Wrapping long comments in the editor.

    Post
    Hello, Thank you for your inquiry. Generally wrapping code lines is currently not available in Embedded Studio editor. This has however been requested before by our customers and will be added in the future. Currently we do not have a fixed time…
  • SEGGER - Nino -

    Replied to the thread 5K monitor doesn't work with Segger embedded Studio.

    Post
    Hello, Thank you for your inquiry. We will try to reproduce the reported behaviour and see if it can be improved. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread Nordic License on MacOS Not Working.

    Post
    Hello, Thank you for your inquiry. Did you make sure that the project your are building debugging is using a Nordic device? The license is only valid for project where Nordic devices are selected. Further troubleshooting steps can be found here:
  • SEGGER - Nino -

    Replied to the thread Glaring Omission from SES Manual - Include Paths ?.

    Post
    Hello, Thank you for your feedback. We will evaluate if the wording can be improved in the manual. As for the how this would be something for our Wiki probably. Best regards, Nino
  • Hello, Thank you for your inquiry. This is indeed possible. For example I have around 30 different versions installed currently. Just make sure not to install them to the same folder otherwise the installer will try to upgrade the older version. Best…
  • SEGGER - Nino -

    Replied to the thread Dark mode on Mac and Linux.

    Post
    Hello, Thank you for your inquiry. To enable dark mode go to Tools->Options->Environment->User Interface->Theme and set it to Dark. This should make whole Embedded Studio dark. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread flash_placement Definition.

    Post
    Hello, Thank you for your inquiry. These macros are either defined in the memorymap.xml of your project or if that is not available by the project setting Code->Build->Memory segments Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread Open Flashloader + interrupts.

    Post
    Hello, Thank you for your inquiry. Interrupts are disabled by default for open Flashloader and can't be used. What target device are you writing a flash loader for if I may ask? Usually there would be no need for interrupts in a flash loader. Best…
  • SEGGER - Nino -

    Replied to the thread JLink wont connect to i.MX6UL EVK.

    Post
    Hello, Thank you for your inquiry. Such an issue is not known to us. Could you check connection with J-Link Commander? wiki.segger.com/J-Link_cannot_…ty_using_J-Link_Commander If it does not work as well could you try SWD instead, does that work? Which…
  • SEGGER - Nino -

    Replied to the thread Ozone watched data window.

    Post
    Hello, Thank you for your feedback. 1: We will evaluate how this can be improved further. 2: Could you provide an example with screenshots so we get a better idea on when the issue happens? What is unintuitive and what would improve the reordering in…
  • SEGGER - Nino -

    Replied to the thread GDB doesn't correctly flash mx29lv160db nor flash.

    Post
    Hello, Thank you for your inquiry. Per supported devices list the AT91M40800 external Flash is only supported as parallel CFI compliant Flash. So you have to make sure that the target specific initialization for the Flash controller is executed…
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Flasher Portable Plus Stand Alone Mode with ADuC7023.

    Post
    Hello, Thank you for your inquiry. Your Flasher seems to be in valid support period. Could you create a support request through our official support channels? This forum is no support forum. More information on how to open a request can be found in my…
  • SEGGER - Nino -

    Replied to the thread JLink-Base iMX7D (M4) eclipse debugging problem.

    Post
    Hello Majd, Thank you for your inquiry. Such an issue is not known to us. As it seems to be working in Ozone but not in Eclipse the reason for this behaviour most likely lies in the sequence used by Eclipse for connection which does not seem to be…
  • SEGGER - Nino -

    Replied to the thread JFlash Cypress PSoC Protection.

    Post
    Hello Vikram, Thank you for your inquiry. Which PSoC are you using exactly? As stated in the Wiki article the unlock sequence is target specific and must be done by the user e.g. via a JLinkScript file. More information about JLinkScript files can be…
  • SEGGER - Nino -

    Replied to the thread Code Formatting from Command Line.

    Post
    Hello Russ, Thank you for your inquiry. Currently code formatting can only be triggered on a per file basis. There are no plans to expand this feature on solution basis or to make it available via command line. Best regards, Nino