[ABANDONED] STM32WB15CC Stack upgrade

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • [ABANDONED] STM32WB15CC Stack upgrade

    Hello everyone,

    following what's described at wiki.segger.com/ST_STM32WB, I'm trying to update the STM32WB15CC's stack using J-Link.
    But it seems that it doesn't work in this mcu. I'm using nucleo board and I can do everything, except stack upgrades.

    Here follows J-Link Commander output:

    Source Code

    1. C:\Program Files\SEGGER\JLink>JLink.exe -autoconnect 1 -device "STM32WB15CC - FUS" -if swd -speed 4000
    2. SEGGER J-Link Commander V7.66a (Compiled May 19 2022 15:19:28)
    3. DLL version V7.66a, compiled May 19 2022 15:18:08
    7. Connecting to J-Link via USB...O.K.
    8. Firmware: J-Link V9 compiled May 7 2021 16:26:12
    9. Hardware version: V9.20
    10. S/N: 269200409
    11. License(s): FlashBP, GDB
    12. OEM: SEGGER-EDU
    13. VTref=3.329V
    14. Device "STM32WB15CC - FUS" selected.
    19. Connecting to target via SWD
    20. Found SW-DP with ID 0x6BA02477
    21. DPIDR: 0x6BA02477
    22. CoreSight SoC-400 or earlier
    23. Scanning AP map to find all available APs
    24. AP[2]: Stopped AP scan as end of AP map has been reached
    25. AP[0]: AHB-AP (IDR: 0x24770011)
    26. AP[1]: AHB-AP (IDR: 0x84770001)
    27. Iterating through AP map to find AHB-AP to use
    28. AP[0]: Core found
    29. AP[0]: AHB-AP ROM base: 0xE00FF000
    30. CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
    31. Found Cortex-M4 r0p1, Little endian.
    32. FPUnit: 6 code (BP) slots and 2 literal slots
    33. CoreSight components:
    34. ROMTbl[0] @ E00FF000
    35. [0][0]: E000E000 CID B105E00D PID 000BB00C SCS-M7
    36. [0][1]: E0001000 CID B105E00D PID 003BB002 DWT
    37. [0][2]: E0002000 CID B105E00D PID 002BB003 FPB
    38. [0][3]: E0000000 CID B105E00D PID 003BB001 ITM
    39. [0][4]: E0040000 CID B105900D PID 000BB9A1 TPIU
    40. [0][6]: E0043000 CID B105900D PID 005BB906 CTI
    41. SetupTarget() start
    42. CORE ID AP[0]: 0x410FC241
    43. FUS: State idle.
    44. Current safe boot version: 0x01020200
    45. Current FUS version: 0x01020200
    46. Current wireless stack version: 0x00000000
    47. SetupTarget() end
    48. Cortex-M4 identified.
    49. J-Link>Mem32 0x58004020, 1
    50. 58004020 = 33FFF1AA
    51. J-Link>r
    52. Reset delay: 0 ms
    53. Reset type NORMAL: Resets core & peripherals via SYSRESETREQ & VECTRESET bit.
    54. BeforeResetTarget() start
    55. BeforeResetTarget() end
    56. ResetTarget() start
    57. J-Link: Target is halted.
    58. ResetTarget() end
    59. AfterResetTarget() start
    60. AfterResetTarget() end
    61. J-Link>loadfile "C:\Users\tiller\STM32Cube\Repository\STM32Cube_FW_WB_V1.13.3\Projects\STM32WB_Copro_Wireless_Binaries\STM32WB1x\stm32wb1x_BLE_Stack_full_extended_fw.bin", 0x08019800
    62. Downloading file [C:\Users\tiller\STM32Cube\Repository\STM32Cube_FW_WB_V1.13.3\Projects\STM32WB_Copro_Wireless_Binaries\STM32WB1x\stm32wb1x_BLE_Stack_full_extended_fw.bin]...
    63. HandleBeforeFlashProg() start
    64. FUS: State idle.
    65. FUS: Deleting wireless stack...
    66. FUS: Operation started. This process might take a few seconds.
    67. FUS: Service ongoing.
    68. FUS: State idle.
    72. Wireless stack successfully deleted.
    73. HandleBeforeFlashProg() end
    74. J-Link: Flash download: Bank 0 @ 0x08000000: Skipped. Contents already match
    75. HandleAfterFlashProg() start
    76. Wireless stack found. WS delete was not successful. Secure sector found at :0x00000000
    77. HandleAfterFlashProg() end
    78. O.K.
    79. J-Link>con
    80. Device "STM32WB15CC - FUS" selected.
    85. Connecting to target via SWD
    86. Found SW-DP with ID 0x6BA02477
    87. DPIDR: 0x6BA02477
    88. CoreSight SoC-400 or earlier
    89. AP map detection skipped. Manually configured AP map found.
    90. AP[0]: AHB-AP (IDR: Not set)
    91. AP[0]: Core found
    92. AP[0]: AHB-AP ROM base: 0xE00FF000
    93. CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
    94. Found Cortex-M4 r0p1, Little endian.
    95. FPUnit: 6 code (BP) slots and 2 literal slots
    96. CoreSight components:
    97. ROMTbl[0] @ E00FF000
    98. [0][0]: E000E000 CID B105E00D PID 000BB00C SCS-M7
    99. [0][1]: E0001000 CID B105E00D PID 003BB002 DWT
    100. [0][2]: E0002000 CID B105E00D PID 002BB003 FPB
    101. [0][3]: E0000000 CID B105E00D PID 003BB001 ITM
    102. [0][4]: E0040000 CID B105900D PID 000BB9A1 TPIU
    103. [0][6]: E0043000 CID B105900D PID 005BB906 CTI
    104. SetupTarget() start
    105. CORE ID AP[0]: 0x410FC241
    106. FUS: State idle.
    107. Current safe boot version: 0x01020200
    108. Current FUS version: 0x01020200
    109. Current wireless stack version: 0x00000000
    110. SetupTarget() end
    111. Cortex-M4 identified.
    112. J-Link>r
    113. Reset delay: 0 ms
    114. Reset type NORMAL: Resets core & peripherals via SYSRESETREQ & VECTRESET bit.
    115. BeforeResetTarget() start
    116. BeforeResetTarget() end
    117. ResetTarget() start
    118. J-Link: Target is halted.
    119. ResetTarget() end
    120. AfterResetTarget() start
    121. AfterResetTarget() end
    122. J-Link>loadfile "C:\Users\tiller\STM32Cube\Repository\STM32Cube_FW_WB_V1.13.3\Projects\STM32WB_Copro_Wireless_Binaries\STM32WB1x\stm32wb1x_BLE_Stack_full_extended_fw.bin", 0x08019800
    123. Downloading file [C:\Users\tiller\STM32Cube\Repository\STM32Cube_FW_WB_V1.13.3\Projects\STM32WB_Copro_Wireless_Binaries\STM32WB1x\stm32wb1x_BLE_Stack_full_extended_fw.bin]...
    124. HandleBeforeFlashProg() start
    125. FUS: State idle.
    126. FUS: Deleting wireless stack...
    127. FUS: Operation started. This process might take a few seconds.
    128. FUS: Service ongoing.
    129. FUS: State idle.
    133. Wireless stack successfully deleted.
    134. HandleBeforeFlashProg() end
    135. J-Link: Flash download: Bank 0 @ 0x08000000: Skipped. Contents already match
    136. HandleAfterFlashProg() start
    137. Wireless stack found. WS delete was not successful. Secure sector found at :0x00000000
    138. HandleAfterFlashProg() end
    139. O.K.
    140. J-Link>
    Display All

  • Hi,
    Thank you for your inquiry.

    1) Does this issue still persist with the latest version of the J-Link Software?
    segger.com/downloads/jlink#J-L…twareAndDocumentationPack
    2) Could you please send us a J-Link log file? How to enable:
    wiki.segger.com/J-Link_DLL#Enable_J-Link_Log_File

    Unfortunately, there are no evaluation boards available with a STM32WB15 device,
    so it is hard for us to look into this.

    BR
    Fabian
    Please read the forum rules before posting.

    Keep in mind, this is *not* a support forum.
    Our engineers will try to answer your questions between their projects if possible but this can be delayed by longer periods of time.
    Should you be entitled to support you can contact us via our support system: segger.com/ticket/
    Or you can contact us via e-mail.

  • Hi,
    The problem persists even with latest software.

    It's important to inform you that a evaluation (nucleo) board with STM32WB15 device exists: st.com/en/evaluation-tools/nucleo-wb15cc.html
    I'm attaching the J-link commander output and its log.
    Note: after trying to update stack, it erases current stack and it remains empty after the error.

    Thank you,
    Tiller
    Files

    • Commander Output.txt

      (3.25 kB, downloaded 118 times, last: )

    • log.txt

      (401.34 kB, downloaded 111 times, last: )

  • Hi TIller,
    Thank you for the information.

    We will order the board and have a look at this.
    I will keep you posted.

    BR
    Fabian
    Please read the forum rules before posting.

    Keep in mind, this is *not* a support forum.
    Our engineers will try to answer your questions between their projects if possible but this can be delayed by longer periods of time.
    Should you be entitled to support you can contact us via our support system: segger.com/ticket/
    Or you can contact us via e-mail.