Search Results

Search results 1-20 of 1,000. There are more results available, please enhance your search parameters.

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • Hello, Thank you for your inquiry. The reported behaviour does not seem to be related to issues in SEGGER software. So please understand that we can't put much time into this request as it is user responsibility to debug and write user code. But as a general tip make sure all code optimizations are disabled and make sure that variables are defined in a way that the compiler may not optimize variables away. How to do this can be found in numerous online resources. For debugging this we recommend …

  • Hi, we received your request via our support system in parallel. To avoid duplicate or even lost information between channels this thread will be closed now and continued via our support system. Best regards, Nino

  • Hello, Thank you for your inquiry. You are correct. The stackoffset was not calculated correctly for FPU applications. This will be fixed with the next J-Link software release. Our samples will also be updated accordingly. Sorry for any inconveniences caused. Best regards, Nino

  • Hello, Thank you for your inquiry. Any chip that is supported by J-Link and supports background memory access can be used fully with SystemView: So yes, the STM32F750N8 is supported. Best regards, Nino

  • Hello Bjoern, Thank you for your inquiry. To pass e.g. versioning information during your build process we recommend using project macros which then can be defined as a preprocessor define: A thread discussing something similar can be found here: [SOLVED] User defined macros expansion To start your builds automatically via command line you can use emBuild: Best regards, Nino

  • Hello, Thank you for your inquiry. You registered with a J-Link EDU but are using a company email address. Please note that the J-Link EDU may not be used in any commercial context as this would be a license violation and illegal. Could you clarify your situation here, why are you using the EDU model? Could you name your Embedded Studio license number for reference? According to the user manual for the MM32L062NT there is no EEPROM at 0x08006000. Could you clarify which manual for this device yo…

  • Hello, Thank you for your inquiry. Could you provide more information on what is not working? Could you provide a small example project that shows that behaviour? Best regards, Nino

  • Hi, It appears that the documentation is not accurate anymore. Sorry for that. You can find it in project options under Code->Build->Project Macros. Best regards, Nino

  • Hi, Thank you for your inquiry. When using the SEGGER Linker section macros are not needed as the SEGGER Linker offers more flexibility in the linker script itself so you can define symbols, regions etc. all in the script and thus have only one point of edit should things change. For reference the Linker manual can be found here: How to switch from gnu linker to SEGGER Linker is explained here: As a base we recommend…

  • Hi AQ, yes, I understood you the first time around. Ozone offers a scripting interface for that. In this case you would use conditional breakpoints. You can do that either via the GUI, automatically in the Ozone project script, or manually in the Ozone Console window if you do not like to use the GUI. An example on how use user actions automated is shown here: For more information see the Ozone reference manual. Best regards, Nino

  • Hello, Thank you for your explanation. Sorry I understood you incorrectly before. For such deployment setups you can use project macros the same way as you would use the global macros with the difference that it is saved on project level and thus protable. For more information see the documentation linked in my last post. Best regards, Nino

  • Hi, Thank you for your feedback. We will add this to our improvements list. Best regards, Nino

  • Hi, Thank you for your inquiry. The reported behaviour was reproducible and will be improved. A quick test through numerous Ozone versions shows that Ozone always behaved this way. Best regards, Nino

  • Hi, Thank you for providing the video. That you are watching Flash memory here is a crucial hint, J-Link caches the Flash content after a download. See here for more information: This leads to the effect you see here, as for the J-Link the Flash memory area was untouched by J-Link so the cache stayed untouched, so no need to update. When you "reopen" the memory window J-Link will do a readback. To avoid the caching you can disabled it either…

  • Hi, Thank you for your inquiry. The reported behaviour is reproducible and will be improved. Sorry for any inconveniences caused. Best regards, Nino

  • Hello, Thank you for your inquiry. For such a setup custom global macros can be used. You can set them under Tools->Options->Building->Global macros How to utilize the is explained here: So one setup could be that you set the APP_VER macro as global macro which then you can use as the CL argument for the post build step and pass it to another preprocessor define. That way both options will reference the same macro. Is this what you are looking for? Best r…

  • Hello, Thank you for your inquiry. Such an issue is not known to us. Could you provide a J-Link log file of the failing session? How did you create the project that you are testing with? Did you use the project wizard to set up a new project? We recommend using the CPU support package for this:…o/technology/cpu-support/ Best regards, Nino

  • Hello Sam, Thank you for your inquiry. There is no conversion tool for the different script types available. For reference we recommend to create a new nrF52 project using CPU support package:…o/technology/cpu-support/ This will create a simple hello world example with a memory map and a SEGGER Linker script that can be used for reference. For more information see the linker documentation: Best regards, Nino

  • Hello, Great to hear that you are up and running again. For completeness a general guide on how to use external toolchains with ES is explained here:…hain_with_Embedded_Studio This thread will be closed now. Best regards, Nino

  • Hi, I tried to reproduce the behaviour with the additional information but everything is working fine for me even after letting it run over 2 hours. It appears to be setup specific. Could you provide an example project that would run on some eval board with which the behaviour was reproducible with? Is the behaviour reproducible more often if you decrease the data buffer size for the data graph? Best regards, Nino