Search Results

Search results 1-20 of 94.

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • Hi Victor, Thank you for your inquiry. It looks like you are writing to 0x00000000, not to 0x10000000. Are you trying to download a .bin file? If so, you will have to add the starting address of where to download the file as well: Syntax: loadfile <filename> [<addr>] Example: loadfile %pathToFile%\somedata.bin 0x10000000 If this does not solve the problem: Could you please send us a screenshot of the full commander output? Could you please send us a J-Link log file? How to enable: wiki.segger.co…

  • Hi, Thank you for your inquiry. I think there is a misunderstanding here. J-Flash is not able/supposed to program RAM. Also, what ever is written to the RAM, will be lost after reset anyway. It looks to me like you have a memory dump (.hex-file) and want to program the application in it to your target. The RAM data of the memory dump was written from the target application which is placed in the flash area. Therefore, it should not be necessary to program the RAM, since it will be written by the…

  • Hi, Thank you for your inquiry. Such an issue is not known to us. Could you please tell us which XPlained Pro board you are referring to? There are multiple boards with that name. Could you please send us a screenshot of the full J-Link Commander output? Could you please send us a J-Link log file? How to enable: wiki.segger.com/J-Link_DLL#Enable_J-Link_Log_File Best regards, Fabian

  • Hi Sébastien, Thank you for your inquiry. We are analyzing an issue regarding the STM32G431-series right now. What you are experiencing seems to be connected to this issue. We will come back to you as soon as we have news about this. Best regards, Fabian

  • Hi, Thank you for your inquiry. Such an issue is not known to us. Could you please tell answer the following questions: 1) What device are you trying to get data from? 2) Do you get RTT output, when using a local setup (using RTT Viewer on the same PC as the J-Link is connect to, without Remote Server)? 3) Do you use custom hardware or an evaluation board? In the latter case which one? If custom hardware, do you experience the same problem on an evaluation board? 4) Could you please send us a sc…

  • Hi, Thank you for your inquiry. Such an issue is not known to us. Does this behavior also appear when using the newest J-Link Software and Documentation Pack version? You can download it here: If so, could you please verify if the target was successfully programmed and running after executing the script? Best regards, Fabian

  • Hi, Thank you for your inquiry. Such an issue is not known to us. Do you use custom hardware or an evaluation board? In the latter case which one? If custom hardware, do you experience the same problem on an evaluation board? Could you please send us a J-Link log file? How to enable: wiki.segger.com/J-Link_DLL#Enable_J-Link_Log_File Could you please erase the target via J-Link Commander and tell us if it works?: - Open the J-Link commander - Connect to the target - Write "erase" to erase the dev…

  • Hi Pawel, Sorry for the delay in response. We were able to reproduce the issue and are looking into it right now. Best regards, Fabian

  • Hi, Thank you for your inquiry. We tried to reproduce the issue. On the BCM43907 / CYW43907 WICED kit everything is working as expected. As we also answered your questions in our support ticket system we will consider this case as closed now. Best regards, Fabian

  • Hi Mark, Thank you for your inquiry. Since you contacted us via Support System, we will close this thread to make sure no information is lost between the channels. Best regards, Fabian

  • Hi Johannes, Sorry for the delay in response. We recently had a customer who had a similar problem. According to him the problem was caused by some switches on the evaluation board, which were not set correctly. Could you please check this? Did you contact Hilscher support? They might also know something about this. Best regards, Fabian

  • Hi Thomas, Thank you for your inquiry and sorry for the delay in response. We are able to reproduce this. Thank you for making this known to us. We will see if we can find a solution for this that works out of the box. As a work around you could write your own script where you implement the solution provided in the article. Best regards, Fabian

  • Hi, Yes, you can also reset the config area via J-Link Commander: Please connect to the J-Link and type "resetconf" (without quotations). After doing so: Is it now possible to connect to the J-Link EDU mini via J-Link Configurator? Best regards, Fabian

  • Hi Henry, Thank you for your feature suggestion. I will forward this to the corresponding department and we will discuss this internally. Best regards, Fabian

  • Hi, Did the reset of the config area work though? Just to eliminate the possibility that this problem is connected to the J-Link Configurator: Could you please try to update the firmware via the J-Link Commander? Just open the J-Link Commander and connect to the J-Link EDU Mini. This should prompt the update dialog. Best regards, Fabian

  • Hi Robson, I am happy to hear that you are up and running again. We will consider this case as closed now. Best regards Fabian

  • Hi Robson, It seems that the WB50 is compatible to the WB55 devices. Unfortunately, there is no reference manual and no evaluation board available for this device. Therefore we see the following 3 options: - If the devices are indeed compatible, you could just select "STM32WB55" as device. - You could provide us with 2 hardware samples and we implement regular support. - You could add support via OFL (as mentioned above). Best regards, Fabian

  • Hi, Thank you for your inquiry. Such an issue is not known to us. Did you write the config area of the J-Link? The nickname looks broken. Did you set a nickname for your J-Link? Could you please try to do the following in the J-Link Configurator: - reset the config (right click on the J-Link and press "Reset config") - replace the firmware (right click on the J-Link and press "Replace firmware") Best regards, Fabian

  • Hi Robson, Thank you for the information. I will keep you posted. As a side note: You can also implement support for the device yourself via Open Flashloader. For more information please follow this link: wiki.segger.com/Open_Flashloader Best regards, Fabian

  • Hi Stefan, Thank you for your inquiry. We received your email via our support system and we will get back to you there, since you are still in support period. We will close this thread to keep communication to one channel, to make sure no information gets lost that way. Please keep communication to one channel for further cases. Best regards, Fabian