Search Results

Search results 1-10 of 10.

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • Thank you very much!

  • Hi there, Can I know if JTrace can support the NuMaker PFM-M2351 board out-out-box? The board has a cortex debug+ interface, but I didn't find information on the tested device page (segger.com/products/debug-prob…echnology/tested-devices/). direct.nuvoton.com/en/numaker-pfm-m2351 Moreover, can anyone confirm if the board has ETB support? Thanks!

  • Thank you Nino. You are really helpful.

  • Currently, Ozone reported the following coresight components: CoreSight components: ROMTbl[0] @ E00FE000 ROMTbl[0][0]: E00FF000, CID: B105100D, PID: 000BB4C9 ROM Table ROMTbl[1] @ E00FF000 ROMTbl[1][0]: E000E000, CID: B105900D, PID: 000BBD21 Cortex-M33 ROMTbl[1][1]: E0001000, CID: B105900D, PID: 000BBD21 DWT ROMTbl[1][2]: E0002000, CID: B105900D, PID: 000BBD21 FPB ROMTbl[1][3]: E0000000, CID: B105900D, PID: 000BBD21 ITM ROMTbl[0][1]: E0040000, CID: B105900D, PID: 000BBD21 Cortex-M33 I suppose th…

  • Hi there, I have a LPC55S69 EVK board and wanted to use the Jtrace to get the instruction trace. Since no trace pin is available on the board, I thought setting trace source to be "trace buffer" should work. Unfortunately, it is not allowed in OZone. I wonder if this is a hardware issue or software issue. More specifically, Is it because the hardware lacks the ETM/ETB support or the JLINK software hasn't supported it yet? Thank you very much!

  • Quote from SEGGER - Nino: “You can get around this by exporting the instruction trace data after each stop. This can also be automated. See here for more details: wiki.segger.com/Automated_Tests_with_Ozone ” Thanks for the guide. I used Trace.ExportCSV() to export a file on every breakpoint. However, the file name can only be provided with a constant string. Any way to give a distinct file name on each invocation of Trace.ExportCSV()? For example, a self-increasing static/global integer which ca…

  • Quote from SEGGER - Nino: “2: Currently not possible. ” If I buy SDK now, can I get a free update with that feature?

  • Hi Nino, Thanks for the reply. Quote from SEGGER - Nino: “We are currently working on expanding Ozone and J-Trace PRO so you can select to buffer more data into either your host PCs RAM or to one or multiple trace files. ” 1: Do I need a new J-Trace POR hardware to use this feature? 2: Can I use the SDK to save the trace to files already? Thanks!

  • Hello, It seems there is a hard limit on the captured instructions. In my case, the number of instructions is limited at around 67M, even though I set "Maximum instruction count" to 10G. I wonder if this is a hard limit or something configurable elsewhere. In addition, whenever I stop the target, previous trace is lost. Is there an option to retain previous trace when resuming at break point? Thanks!

  • Hello, I need to capture both ETM and ITM trace at the same time. If I understand correctly, if trace pins are used, both ETM and ITM data are routed to J-trace. However, in the manual of Ozone, it is state that "The simultaneous use of multiple trace data channels in Ozone is currently not supported". Here I think data channels refer to trace pins/trace buffer/swo. My question is, if I chose trace pins, can I get instruction trace and ITM data simultaneously in Ozone? If not, is it supported in…