Search Results

Search results 1-20 of 1,000. There are more results available, please enhance your search parameters.

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • Hello, Quote from tdl7rt: “I mean in the FlashDevice config struct: ” In that case see here: wiki.segger.com/Open_Flashloader#SectorInfo Quote from tdl7rt: “No it does not need, but I was adapting existing ST HAL code which depends on having a Systick available for the timeout function. ” A timeout function should not be necessary for a standalone flash loader so we recommend not using Systick here. Also generally as stated before using the ST HAL is not recommended as this can lead to many unwa…

  • Hello, Please understand that CFi init is user responsibility and leaves our regular support scope so we can't offer assistance in this case. Generally the ConfigTargetSettings looks correct if the addresses are correct. For the target specific CFI init we suggest contacting Atmel/Microchip support. Best regards, Nino

  • Hello, Thank you for your inquiry. Such an issue is not known to us. The UniFlash is not our software so we can't comment on it working or not. But you should be able to Flash the MSP432P4 with Segger software like J-Link Commander or J-Flash. They are available in your J-Link software install folder. Could you try Flashing with J-Link Commander for example? wiki.segger.com/J-Link_cannot_…ty_using_J-Link_Commander After successful connect use command loadfile and specify the binary/hex that shou…

  • Hello, Which J-Link software version are you using when trying to unlock? With the latest version you should get a pop up asking if you want to unlock the device. Do you get an unlock pop up when using the latest J-Link software version and does selecting yes unlock the device? What OS does your production PC run? Best regards, Nino

  • Hi Daniel, Could you elaborate what you would need interrupts for? To our knowledge the L5 series do not need interrupts for operating the Flash controller. Quote from tdl7rt: “Another question, is there a limit on the section size? ” What exactly do you mean with section size? Size of the RAMCode? Or section size of the Flash chip? If you are looking to use a third party library from ST to create the Flash loader we strongly suggest not to use it as such libraries usually use code parts which a…

  • Hello, Thank you for your inquiry. Generally wrapping code lines is currently not available in Embedded Studio editor. This has however been requested before by our customers and will be added in the future. Currently we do not have a fixed time schedule for this. To stay up to date regarding Embedded Studio updates subscribe here: segger.com/notification/subscribe.php?prodid=196 Best regards, Nino

  • Hello, Thank you for your inquiry. We will try to reproduce the reported behaviour and see if it can be improved. Best regards, Nino

  • Hello, Thank you for your inquiry. Did you make sure that the project your are building debugging is using a Nordic device? The license is only valid for project where Nordic devices are selected. Further troubleshooting steps can be found here: wiki.segger.com/Get_a_License_…dic_Semiconductor_Devices Best regards, Nino

  • Hello, Thank you for your feedback. We will evaluate if the wording can be improved in the manual. As for the how this would be something for our Wiki probably. Best regards, Nino

  • Hello, Thank you for your inquiry. This is indeed possible. For example I have around 30 different versions installed currently. Just make sure not to install them to the same folder otherwise the installer will try to upgrade the older version. Best regards, Nino

  • Hello, Thank you for your inquiry. To enable dark mode go to Tools->Options->Environment->User Interface->Theme and set it to Dark. This should make whole Embedded Studio dark. Best regards, Nino

  • Hello, Thank you for your inquiry. These macros are either defined in the memorymap.xml of your project or if that is not available by the project setting Code->Build->Memory segments Best regards, Nino

  • Hello, Thank you for your inquiry. Interrupts are disabled by default for open Flashloader and can't be used. What target device are you writing a flash loader for if I may ask? Usually there would be no need for interrupts in a flash loader. Best regards, Nino

  • Hello, Thank you for your inquiry. Such an issue is not known to us. Could you check connection with J-Link Commander? wiki.segger.com/J-Link_cannot_…ty_using_J-Link_Commander If it does not work as well could you try SWD instead, does that work? Which revision of the i.MX6UL EVK do you use? Best regards, Nino

  • Hello, Thank you for your feedback. 1: We will evaluate how this can be improved further. 2: Could you provide an example with screenshots so we get a better idea on when the issue happens? What is unintuitive and what would improve the reordering in your opinion? 3: This sounds like unwanted behaviour. We will try to reproduce the behaviour and report back with our findings. Best regards, Nino

  • Hello, Thank you for your inquiry. Per supported devices list the AT91M40800 external Flash is only supported as parallel CFI compliant Flash. So you have to make sure that the target specific initialization for the Flash controller is executed correctly. A JLinkScript file can be used for such a task. Best regards, Nino

  • Hello, Thank you for your inquiry. Your Flasher seems to be in valid support period. Could you create a support request through our official support channels? This forum is no support forum. More information on how to open a request can be found in my signature. Best regards, Nino

  • Hello Majd, Thank you for your inquiry. Such an issue is not known to us. As it seems to be working in Ozone but not in Eclipse the reason for this behaviour most likely lies in the sequence used by Eclipse for connection which does not seem to be working. Please understand that we can't provide assistance for issues in software that is not created or maintained by us. We suggest using Ozone instead. Best regards, Nino

  • Hello Vikram, Thank you for your inquiry. Which PSoC are you using exactly? As stated in the Wiki article the unlock sequence is target specific and must be done by the user e.g. via a JLinkScript file. More information about JLinkScript files can be found in the J-Link user manual. For the target specific unlock sequence we recommend contacting Cypress support. Best regards, Nino

  • Hello Russ, Thank you for your inquiry. Currently code formatting can only be triggered on a per file basis. There are no plans to expand this feature on solution basis or to make it available via command line. Best regards, Nino