Search Results

Search results 1-20 of 1,000. There are more results available, please enhance your search parameters.

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • Hello, Quote from dnfuss: “or does a full implementation of getregs give enough for display of callstack? ” Yes that is all information that is needed. Regarding the callstack. This can only be reconstructed if the stack frame information is available. For interrupts it is possible that the stack frame is not available. Please see the getregs() implementation of the embOSPLugin.js for reference. There everything is implemented correctly. Please understand that we can't put more time into this in…

  • Hi, Thank you for providing the reproduction steps via the video. The issue is reproducible and we are investigating. Best regards, Nino

  • Good to hear. Case closed

  • Hello Tom, We have an updated C++ STL planned for this year. A fixed time schedule is not known yet. To get automatically notified when new Embedded Studio versions are released you can subscribe here: segger.com/notification/subscribe.php?prodid=196 Best regards, Nino

  • Hello, Thank you for your inquiry. Correct the pex file is the equivalent to the JLinkScript, just not in source form. We could provide you with the J-LinkScript source for reference. You can request it via our support system. See my signature for the link. Make sure to add information about the reason why you need the source and specify if something is not working as expected. A .jdebug variant is not available as the trace pin init has to be done at a specific point during debugging. Using the…

  • Hello, Yes, there are situations. However if you are not instructed by our support team to change it, you should not change it. Best regards, Nino

  • Hello, Thank you for your inquiry. Such an issue is not known to us. Currently we assume it is a setup/target application issue. Could you provide an example project for reproduction that would run on the mentioned eval board? Best regards, Nino

  • Hello, Thank you for your feedback. The mentioned C++ features are on our wishlist but with no fixed time schedule. Improvement of the dark mode is on our ToDo but with no high priority. The find and replace is limited on purpose to make accidental replaces impossible as a solution can have thousands of files. But we will see if this can be improved to be easier accessible or at least available optionally. Best regards, Nino

  • Hello Michael, Thank you for your inquiry. A Ozone updated is planned for this week which will come with the latest J-Link library version. To get a notification you can subscribe here: segger.com/notification/subscribe.php?prodid=7 For Linux and Windows users that stumble upon this. You can always update the J-Link library within Ozone either manually or by using the J-Link DLL Updater (Windows). Best regards, Nino

  • Hello David, Yes that is possible. if the Plugin is fully implemented callstack, registers, etc. will always show the context of the currently selected task in the plugin window. It was essentially discussed here: [SOLVED] RTOS plugins For reference we recommend to use the embOS plugin source where this feature is available as well. Best regards, Nino

  • Hello, FYI this issue has been fixed and will be available with Ozone V3.22b which is planned to be released this week. Best regards, Nino

  • Hi Detlef, OK I see. Thank you for clarifying. Good to hear that you are up and running again. We will consider this thread as solved now. Best regards, Nino

  • Hello Detlef, I must say I am a bit confused now. First the inquiry was related to Ozone with Keil output. Now you are using Embedded Studio. Is the issue resolved or not? What is working and what is not working? Best regards, Nino

  • Hello, Thank you for your inquiry. Ozone will use the same reset JLinkExe uses as default, so there is probably something else wrong with your project setup. For reference here are guides on how to set up Ozone to debug setups with e.g. bootloaders: wiki.segger.com/Debug_on_a_Target_with_Bootloader wiki.segger.com/Debug_Bootload…ion_in_same_Ozone_project We do not recommend to overwrite the TargetReset() function and should only be overwritten where the default reset behaviour is not working and…

  • Hello, Thank you for your inquiry. The SEGGER-CC is our stable release version which is recommended for development. The SEGGER-CC-NG is essentially a preview version of the SEGGER compiler that has experimental features and is always based on the latest clang trunk which usually is also stable but requires some longer testing by us, before features are moved from the -NG compiler to our stable release. I hope this clarifies how the two compiler variants should be used and what to expect from th…

  • Hello, To achieve this you can do one of the following two things. 1. Either leave the host Connection field empty. This will default then to USB, so if only 1 J-Link is connected to the PC it will work out of the box. For IP setups the initial connection will fail and ask if the network should be searched for J-Links. 2. You can write a solution file which configures the specific host connection settings. This solution then imports the actual project with all the other settings. That way you on…

  • [SOLVED] RTOS plugins

    SEGGER - Nino - - Ozone related

    Post

    Hello, Great to hear that you got it up and running and thank you for sharing with the community. We will make sure to point users to your github when looking for a ThreadX script. Regarding your documentation feedback we will discuss this internally and see where it can be improved further. Happy debugging! We will consider this thread as solved now. Best regards, Nino

  • Hello, Thank you for your inquiry. Such an issue is not known to us. Which version of Ozone are you using? The code snippet seems to have an error. Did you mean to post it with one less closing bracket? Which compiler do you use for code generation? Are any optimizations active? What target device are you debugging exactly? Best regards, Nino

  • Hello, Thank you for your inquiry. The System Include Directories is used to set the path to the stdlib that is supplied with Embedded Studio. We recommend not to alter it. For any other include paths that are set for external software we recommend to use user include directories. Best regards, Nino

  • Hi Andy, Great to hear that you are up and running again. We will consider this thread as solved now. Best regards, Nino