Search Results
Search results 1-15 of 15.
This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.
-
I have some more information that may help. This may require an updated to the Flash programming algorithm: This is probably cause by two reasons: 1. JLINK try to operate flash before flash self-initialization is done.(operate flash immediatly after RESET) 2. JLINK's flash algorithm try to read to an empty flash content(will cause hard fault.) for 1: the flash algorithm need to wait for flash self-initlization is done, which means INT_STATUS register bit2 is set and bit 0 and bit 1 is cleared(no…
-
I have run into a issue where I cannot connect to an LPC55S69 which is "factory fresh". In this state, the MCU will enter its ROM bootloader as there is not valid application in Flash. I am working with NXP on determining what the initialial state of the Flash memory and what configuration bits are. I can get a J-Link to program, erase, etc if I connect using a CMSIS-DAP probe (I am using an LPC-LINK II with MCU XPresso). Once I use MCUXPresso and a CMSIS DAP adapter to program the device (or ev…
-
I just upgraded to Ozone 3.20. I had an existing project for an LPC4357 that nopt longer functions. I noticed it no longer had the CPU association. I tried to create a new project and the device selection wizard is wrong. The LPC4357 is NOT made by OKDI nor is a Cortex A5. I reverted to V3.10 (released in December) and I was able to program/debug. I have attached my .jdebug file
-
Is it possible to get ozone to support relative paths to the .jdebug / project file. For example in my .jdebug: Project.SetDevice ("LPC4357_M4"); Project.SetHostIF ("USB", ""); Project.SetTargetIF ("JTAG"); Project.SetTIFSpeed ("1 MHz"); Project.AddPathSubstitute ("C:/ELI/SmartBrew/SRC/embedded/TempControl/SRC/TC4", "$(ProjectDir)"); Project.AddSvdFile ("$(InstallDir)/Config/CPU/Cortex-M4F.svd"); Project.AddSvdFile ("$(ProjectDir)/LPC43xx_43Sxx.svd"); The problem I am having is that $(ProjectDir…
-
I have a Nordic PCA10040 (dev kit for the NRF53832) which has an integrated J-LINK. When I connect to the PC there is also a JLINK CDC UART Port. It appears that the device has enumerated correctly. When I try to connect to the port via putty I get an error that I cannot connect (picture attached). I was able to connect to this board via Segger Embedded Studio, load code, debug, etc. I have also tried to connect to the com port via a Python Script provide by nordic which give as "permission deni…
-
I saw int he release notes for 2.56m that automatic refreshed is disabled by default. When I tried my project from 2.56e, It seems there is no way to turn on refreshing of variables. When i right-click in the "Watched Data"view and select a refresh other an "off" (for example 1Hz), It will immediately return to "off" as soon as I start debugging. I tried turning on refresh it with the target paused and while it was running and got the same results. It does not seem like there is a way in this ve…
-
Thanks for the Wiki link. I was unware of it. You can mark this thread as solved.
-
Just a bump on this. I recently grabbed Jlink6.31d (beta). Ozone now appears to work. My test application can single step, etc. I did notice that there a couple i.MX RT1052 options. in particular there is a MIMXRT1052xxxxA and a MIMXRT1052xxxxB What is the difference? I looked in the JLinkdevices.xml Source Code (1 line) "A" and "B" appear to be identical as they both use a hyper flash driver. I though one might be for QSPI flash programming but "NXP_iMXRT105x_QSPI.elf" is never specified. (I fo…
-
Hello: I have a .jlinkscript file that is being passes to jlink.exe with NXP's MCUXpresso Tool. I wish to use it within Ozone. The syntax appears the same as what is in a .jdebug file used by ozone. Can I copy the source into a .jdebug file? What is the proper way to use a .jlinkscript file in an ozone project? (I attached what I am using. I had to add the .txt extention to allow an uplaod to this forum)
-
Hello Nino: Thank you for the response. I followed your instructions: 1.) Saved the .jdebug file 2.) Uncommented the functions TargetReset() and AfterTargetDownload() It seems to get a little further in the process but still hangs. I have attached my .jdebug file that was created by Embedded Studio launching Ozone as well as a capture of the console when the freeze occurs. Note: I had to rename the .jdebug to .jdebug.txt to allow upload to the forum.
-
Hello: I am having a debug issue with the NXP i.MX RT1052EVK with Ozone. Setup: --------------------------- Embedded Studio 3.34 Ozone 2.56e i.MXRT1052 EVK Using External J-LINK debugger on J21 The board is jumpered to boot from HyperFlash (although I am only testing RAM only projects). What is Working: ---------------------------------------- I was abel to create the sample Hello world project in Embedded Studio after installing the 1-52 support package. It could compile and download fine. I co…