Recent Activities

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • Hi, We are using the Segger Emulator JLink Pro for programming our hardware TMS570LS0714 (ARM Cortex-R4F) and using the IDE IAR EWARM 8.22. However, when we are trying to Download and Debug using the IDE IAR EWARM 8.22 , we are getting an error message…
  • Gossamer -

    Replied to the thread Register definition file causing issues.

    Post
    Hi, Attached is the svd file. Issue happens as soon as I attach the svd file and do the first debugging over SWD. I dont even enable any of the peripherals in the register viewer. Didnt try JTAG, as I dont have compatible board. Removing the svd file,…
  • akira -

    Replied to the thread J-Link DLL Updater cannot find my installed Keil uVision.

    Post
    Thanks. I can update. :)
  • roblabla -

    Posted the thread J-Link EDU Jetson TX1 support.

    Thread
    Hello, I am currently looking for an affordable JTAG debugger to debug some open source software on my Jetson TX1. The Jetson TX1 uses Cortex A57 and Cortex A53 cores in a BIG.little architecture. I was wondering if the J-Link EDU supports this, but I'm…
  • PMOR -

    Replied to the thread JLink: avoid the "update firmware" dialog.

    Post
    Small update. We temporarily solved the issue by downgrading to JLink_V600.
  • Veit_Kannegieser -

    Posted the thread Memory zone/background memory access.

    Thread
    Hello, i am trying to get RTT working with our devices, which have Cortex-A9 and Cortex-R4 based controllers on them again. jlink.exe showsSource Code (4 lines) for both. Questions: 1) are the "zone"s of jlink.exe memory commands that zones?, if yes,…
  • mati1485 -

    Posted the thread Displaying BMP file on LPC54628.

    Thread
    Hi, Currently I'm using LPC54628 development board and trying to display any image (BMP in general). I have 32x32 bmp image converted to C file. This is code generated from Bitmap Converter. C Source Code (76 lines) I' d like to simply display it…
  • DSmidgit -

    Replied to the thread J-FLASH not reading external memory LH75401.

    Post
    Hello Nino, I tried your sugestion but I just get the message shown in the image below. forum.segger.com/index.php/Att…176b47e0cb32b965d908d59cd But when i check the memory is not erased. It looks like erase does not do anything because the ERasing…
  • LexaGb -

    Replied to the thread Emwin image draw.

    Post
    Upd. If you do not want to draw the whole image on the screen before copying a half in memory device then you can use another memory device for drawing. This results in only half image displayed on the screen: C Source Code (45 lines) Alex.
  • SEGGER - Nino -

    Replied to the thread Register definition file causing issues.

    Post
    Hello, Thank you for your inquiry. Such an issue is not known to us. Could you provide us with the .svd file for reference? Does this issue happen only if certain peripherals are active or with all of them?` Bestr regards, Nino
  • SEGGER - Nino -

    Replied to the thread [SOLVED] RTT viewer connected but no output with STM32H743.

    Post
    Hello, Thank you for your inquiry. The automatic search range for RTT control block for STM32H7 starts at 0x24... as this RAM is always available. If another memory location is used it has to be set manually by the user. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread J-Link DLL Updater cannot find my installed Keil uVision.

    Post
    Hello, If autodetection does not work you can update manually by going into your Keil install directory to Keil/ARM/Segger and replace the JlinkARM.dll with the new one from the latest installed J-Link software package. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread How to read the contents of nor flash?.

    Post
    Hello, Thank you for your inquiry. For the S3C2 series only CFIc ompliant NOR Flash is supported. segger.com/downloads/supported-devices.php If you use such Flash make sure it is initialized. How to is explained in the J-Link user guide UM08001 in…
  • LexaGb -

    Replied to the thread Emwin image draw.

    Post
    Hello, as I noticed the first approach is working for uncompressed bitmaps. If your bitmap is compressed (RLE etc) then it may end with incorrect drawing due to complex compressed data structure. Further it may concern also uncompressed…
  • SEGGER - Nino -

    Replied to the thread J-FLASH not reading external memory LH75401.

    Post
    Hello, When trying to erase with J-Link Commander you should get the message showed in the attached picture. Do you get the same message when typing erase? If yes, could you execute the exec command EnableEraseAllFlashBanks? This should enable you to…
  • anuj.tanksali -

    Replied to the thread Emwin image draw.

    Post
    Hello, Thanks for the reply. I tried the above method and the image displays but is jumbled up. when i give bmhalfImage.XSize = 100; the image does not display properly but when i change it to bmhalfImage.XSize = 200; i.e. original size the whole image…
  • andysec -

    Posted the thread Integrating Pc-Lint plus.

    Thread
    Ide version = 4.10 for ARM Various posts have attempted this, some claiming success with the following tools command :- "$(LINTDIR)\bin\pclp64.exe" -v -incvar(__CW_ARM) -i"$(LINTDIR)\lnt" "$(LINTDIR)\lnt\co-gcc.lnt"…
  • LexaGb -

    Replied to the thread Emwin image draw.

    Post
    Hello, there maybe a way to copy a bitmap structure and change XSize to a half of original size, something like this: C Source Code (34 lines) As far as I understand it is working with uncompressed bitmaps. Maybe a way better is to use memory…
  • Godsmack -

    Posted the thread J-Link firmware issue in BMI change with XMC1 family (Infineon).

    Thread
    Good day. Recently I discovered small mulfinction in latest firmware of J-Link Lite regarding BMI (Boot Mode Index) change in XMC1 with DAVE v4.4.2 software. Related topic: Problem with setting BMI value of Infineon XMC1000 via J-Link Hardware setup: -…
  • anuj.tanksali -

    Replied to the thread Emwin image draw.

    Post
    Hello Richard, I want to do this at runtime dynamically and i dont want to scale the image just display the 200x100 image as it is but display only 100x100 so that the image will display but with half the width and the same height. Regards, Anuj