Recent Activities

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • cymatics -

    Replied to the thread JLink EDU and Renesas HEW and E2 Studio.

    Post
    I have been trying to modify the debug settings including GDB Server settings in E2 Studio, but i cannot get the emulator to actually upload the firmware to my board. However, i can toggle the IO register bits on the RX630 through the E2 interface.…
  • SEGGER - Fabian -

    Replied to the thread How to set JLink to never power the board.

    Post
    Hi, Could you clarify which isolator you are currently using? Does the same behavior occur when using another target board? Could you measure the voltage of the J-Link's 5V-pin when power off perm is used? Do you get the same Voltage reading…
  • SEGGER - Fabian -

    Replied to the thread Cortex M0 Downloading file Unspecified Error -1.

    Post
    Hi, Thanks for your inquiry. Could you please send us a J-Link log file? How to enable: wiki.segger.com/J-Link_DLL#Enable_J-Link_Log_File Could you also send us a screenshot of the full J-Link commander output? Could you also tell us, what chip exactly…
  • cymatics -

    Posted the thread JLink EDU and Renesas HEW and E2 Studio.

    Thread
    Hi, I have not found this issue on the forum, so apologies if it has been covered already. I recently bought a JLink EDU and have started using it with Renesas' HEW and E2 Studio. In the case with HEW, the emulator setup only allowed me to select the…
  • SEGGER - Nino -

    Replied to the thread RTOS plugin when no GDBServer used ( = IDE / tool uses jlink dll ).

    Post
    Hello, Thank you for your inquiry. The IDE and Ozone use different awareness plug ins than GDBServer. ES: wiki.segger.com/Enable_RTOS_Awareness_in_Embedded_Studio Ozone: Shipped with Ozone. Can be found in Ozone installation folder under Plugins. How…
  • Dear Community, Please find the reproduction steps (i.MX6Q): Power cycle the board Stop at U-Boot prompt ./JLinkGDBServerExe -select IP=192.168.2.72 -device MCIMX6Q6 -endian little -if JTAG -speed auto -noir -noLocalhostOnly (gdb) target remote…
  • SEGGER - Florian -

    Replied to the thread GUI_TIMER_Create.

    Post
    Hi Pieter, window timers still do its job when you use multiple windows. You can create and react on timers with different windows, you just need the window handle the timer will be attached to. What applies for both kinds of timers, is that you still…
  • Pieter Eggermont -

    Replied to the thread GUI_TIMER_Create.

    Post
    Hi, I have different windows (multiple pages system) so using a window timer is no option for me. It works now because I defined the time before the main loop once. When I than restart the timer this is working. The case that was not working is…
  • Dear Community, I need to tune the default reset sequence (executed thereafter with 'mo reset'). The problem: ------------------- Stop SoC (i.MX6Q) just after powering it up (in the early SRAM - 0x908000 address in this case). This is necessary for…
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Forum as non support? How about your sale description.

    Post
    Hello, Thank you for your feedback. Quote from v01d: “I find this is nonsense as far as 'not a support forum' goes. Please look on what is printed on the page inside of my purchased Segger J-Link EDU unit, see photo attached. ” Good catch. The EDU…
  • sridhar6994 -

    Replied to the thread images to .DAT files creation using emwin.

    Post
    attachments not supported in previous comments sorry for that messages
  • sridhar6994 -

    Replied to the thread images to .DAT files creation using emwin.

    Post
    attachments
  • sridhar6994 -

    Replied to the thread images to .DAT files creation using emwin.

    Post
    hi Florian Thanks for your reply Actually i can able to create .dta files as you said by selecting the extension. But in my code I am having .DAT files only as I have attached.
  • SEGGER - Florian -

    Replied to the thread GUI_TIMER_Create.

    Post
    Hi Pieter, you have to set a period for the timer using GUI_TIMER_SetPeriod(). Once you did so, calling GUI_TIMER_Restart() will restart that timer with the set period. By the way, when using windows, you might want to use the timer API that is part of…
  • Pieter Eggermont -

    Replied to the thread GUI_TIMER_Create.

    Post
    ok have new results ... What I did on second log in, I've deleted the timer and re-inited it again. this was not working properly in the second time I try to use that timer.. I now init it once, set the time period and just use the restart when I need…
  • Pieter Eggermont -

    Replied to the thread Widget Edit display unexpected length string.

    Post
    Hi, What also could be happening is that the full text is indeed visibile at init but after drawing that text, another widget is drawn over the position of the chars '89abc' . When adding those chars in the PAINT or EDIT or other function after INIT,…
  • SEGGER - Florian -

    Replied to the thread Widget Edit display unexpected length string.

    Post
    Hi Ross Lee, can you tell me what maximum length you set to the EDIT widget when you create it? EDIT_SetMaxLen(hItem, 1000); could fail due to not enough memory being available. Best regards, Florian
  • Pieter Eggermont -

    Posted the thread GUI_TIMER_Create.

    Thread
    Hi, I'm creating an access code window. When entering the correct code, I start a timer which will go off after 60 seconds when no key press was done so the logged in user is logged out again. when entering the code I create following timer: C Source…
  • volodymyr -

    Replied to the thread MULTIPAGE: issue #2 of non-focusable page.

    Post
    Quote from SEGGER - Florian: “just add a button to your dialog with the non-focusable widgets and hide it using WM_HideWindow() ” Hi Florian. Thank you, it really helped.
  • lukma -

    Posted the thread Relocate symbols in OZONE.

    Thread
    Dear community, I would like to ask about using Ozone SW (ver. 2.70.3 - 64 bit Debian) with debugging U-Boot. U-Boot itself work with two sets of "locations". One matches the address set of u-boot elf binary just after starting it from SPL (or loading…