Recent Activities

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • ekodeddy -

    Posted the thread JTAGLoadExe Exit Code:-11.

    Thread
    I am using JLink plus with JTAGLoadExe (Mac version) revision V6.44d to load an embedded program image into Kintex FPGA XCKU15P-2E. The embedded program is to program the FPGA eFuse. However, I often encounter JTAG Load error with exit code -11. And when…
  • LexaGb -

    Posted the thread LISTWHEEL background loses transparency.

    Thread
    Hello to everyone, I have a question implementing a listwheel with semitransparent rounded rect as a background. Here is the code for 320 * 240 desktop: C Source Code (62 lines) All is ok until listwheel reacts on moving. Then it loses…
  • SEGGER - Nino -

    Replied to the thread J-Trace compatible SWD+Trace interface.

    Post
    Hello, Thank you for your inquiry. We do not recommend routing the trace signals to the 2.54 mm header. Trace signals are not specified by Arm for that type of header and most probes expect there to be ground. Some third party probes might break down if…
  • mkerr -

    Posted the thread J-Trace compatible SWD+Trace interface.

    Thread
    I have purchased the J-Trace PRO for Cortex-M processors. My development board has a pinout for SWD ; i.e. section 18.1.2 of the J-Trace User Guide (UM08001). The header on my boards is a 20 way Insulation Displacement Connector (IDC) keyed box header…
  • krufter -

    Posted the thread RTT Viewer CP1251?.

    Thread
    Does RTT Viewer support cyrillic symbols for example CP1251? May be there is a way to support cyrillic without using other terminals?
  • CodesMagic -

    Replied to the thread Request; STemwin Template for STM32H743ZI.

    Post
    Hi dear Awneil and Alex Thanks for reply. I'll check the STM32Cube_FW_H7_V1.5.0 repository next day but It would be great if related script for STemwin be added to the configurator IDE (STM32CubeMX).
  • LexaGb -

    Replied to the thread Request; STemwin Template for STM32H743ZI.

    Post
    Hello, to awneil's link I would add the latest package for STM32H7 that contains a later version 5.44: st.com/en/embedded-software/stm32cubeh7.html Unfortunately, STM32CubeMX doesn't contain code generation scripts with STemWin GUI for STM32H7 so…
  • awneil -

    Replied to the thread Request; STemwin Template for STM32H743ZI.

    Post
    Have you tried the 'Get Software' link here: st.com/en/embedded-software/stemwin.html :?:
  • volodymyr -

    Replied to the thread WM_SetUntouchable.

    Post
    Quote from SEGGER - Schoenen: “Hi, If I get you right you want to make sure that the initial dialog (the one with _cbDialog) don't receive input when the derived dialog is created (_cbDerivedDialog), right? To achieve that you can simply make the…
  • CodesMagic -

    Posted the thread Request; STemwin Template for STM32H743ZI.

    Thread
    I want to build a GUI with STM32CueMX configurator. Graphics Item doesn't exist in Middlewares for STM32H743ZI!!! I'm looking for a template to get start with STemwin on STM32H743ZI (Keil IDE)...forum.segger.com/index.php/Att…c8a13240c4b921849d7733a7c
  • rabbitlennon -

    Replied to the thread Jtrace on NuMaker PFM-M2351.

    Post
    Thank you very much!
  • SEGGER - Schoenen -

    Replied to the thread WM_SetUntouchable.

    Post
    Hi, If I get you right you want to make sure that the initial dialog (the one with _cbDialog) don't receive input when the derived dialog is created (_cbDerivedDialog), right? To achieve that you can simply make the derived dialog modal: C Source Code…
  • awneil -

    Replied to the thread 'Always Rebuild' - not quite what I wanted..

    Post
    Quote from SEGGER - Nino: “We will add your proposal to our feature wish list and see if this could be added in future so the Always Rebuild option would get additional config options ” Thanks - either as additional options to the existing 'Always…
  • awneil -

    Replied to the thread 'Debug Terminal' (RTT) Window - log to file?.

    Post
    Thanks - that would be great.
  • SEGGER - Nino -

    Replied to the thread Jtrace on NuMaker PFM-M2351.

    Post
    Hello, According to the manual this device has no ETB. Only pin trace via ETM seems to be supported. It will most likely not work out-of-the-box as the trace pins need to be initialized first e.g. using a JLinkScript file. How to do it is described…
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Ozone ELF Loading Time.

    Post
    Hello, Thank you for the feedback. Glad to hear that everything is working as expected now. We try to improved Ozone wherever we can which is why we always recommend using our latest software if possible. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread 'Debug Terminal' (RTT) Window - log to file?.

    Post
    Hello, Thank you for your inquiry. Currently there is no option to export debug terminal output from ES to a file other than copy pasting it to a text file. We will add this to our feature wish list so it might be added to a future version of Embedded…
  • SEGGER - Nino -

    Replied to the thread Window/desktop layout.

    Post
    Hello, The emSession file will be update once a solution/project is closed or Embedded Studio is closed. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread 'Always Rebuild' - not quite what I wanted..

    Post
    Hello, Thank you for your inquiry. The Always Rebuild option does not have advanced conditional options. If it is set to yes it will always rebuild just as the name of the option indicates. We will add your proposal to our feature wish list and see if…
  • SEGGER - Nino -

    Replied to the thread Need output in Verilog format.

    Post
    Hello, Thank you for your inquiry. Could you elaborate what exactly you are trying to do? We do not provide any Keil tools as Keil is a different company. If you are looking to do some pre or post compile/build steps you can do so in Embedded Studio…