Recent Activities

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • sanjeev majumdar -

    Replied to the thread Draw jpeg over widgets.

    Post
    Thanks for the reply Sven. GUI_JPEG_Draw() does really fail sometimes and returns 1 but there is no error code defined in emwin manual for this api. For example, when we are trying to overlay a jpeg on a button, we have registered a callback to the…
  • dsula -

    Replied to the thread can't connect to Syntacore SCR1.

    Post
    Thank you for your reply. I've seen the segger wiki post regarding the SCR1. I also downloaded the SCR1/Arty SDK and tried to use it with the Segger studio. It doesn't work. What does this error message mean? ****** Error: CPU-TAP not found in JTAG…
  • SEGGER - Nino -

    Replied to the thread can't connect to Syntacore SCR1.

    Post
    Hello, Thank you for your inquiry. Generally all cores that follow standard RISC-V RV32 implementation are supported by J-Link. Quote from dsula: “I've taken up this issue with Syntacore and according to them J-Link is NOT compatible with SCR1 (as…
  • SEGGER - Nino -

    Replied to the thread Telink single-wire support?.

    Post
    Hello, Thank you for your inquiry. From the google links I could not find what core type the Telink chips are. Generally they are currently not supported. If they are Arm cores then you could add support yourself with our Open Flashloader interface. If…
  • SEGGER - Nino -

    Replied to the thread Ozone Breakpoints not setting correctly.

    Post
    Hello, Thank you for your inquiry. We are not exactly sure what you mean from the example you provided. Could you provide a bigger snipped where one can see where the BP is actually set? What behaviour would you expect? What steps do you take when…
  • SEGGER - Nino -

    Replied to the thread j-link not connect to Renesas RX210.

    Post
    Hello, Thank you for your inquiry. Please be aware that this forum is a community forum so there is no guarantee to receive a response here. We tried to reproduce the reported behaviour but everything was working as expected in our example setup. See…
  • Hi Hans, We received this inquiry via Supportsystem as well. To keep all information in one place this thread will be closed now. For everyone else, the minimum recommended RAM size is 5-6 kB. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread [SOLVED] QSPI Flash on custom IMXRT1021 board.

    Post
    Hello Dave, Thank you for your inquiry. Please be aware that this is no official support forum so there is no guarantee to receive a response here. If you are entitled to support see my signature for more information. Quote from dmarples: “I can't say…
  • SEGGER - Nino -

    Replied to the thread Is it possible to use J-Link EDU to debug Nuvoton's N76E003 over SWD?.

    Post
    Hello, Thank you for your inquiry. What is the actual name of the target device you are looking to debug? Is it on our public supported devices list? segger.com/downloads/supported-devices.php If not but it is one of our supported core types you can add…
  • Hello, Thank you for your inquiry. The folder you are trying to write to is write protected by admin rights. Simply select another saving location for your project file and you should not see this error message anymore. Alternatively operate J-Flash…
  • SEGGER - Nino -

    Replied to the thread [SOLVED] JFlash resets QSPI bit in IS25LP128 flash chip.

    Post
    Hello Hans, We received your inquiry via Supportsystem as well where the topic has been solved. A fixed version will be available with our next J-Link software beta. This thread will be closed now to avoid double information. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Ozone loads elf file very slowly.

    Post
    Hello Hans, Thank you for your inquiry. We received your inquiry via our Supportsystem as well. To avoid double information this thread will be closed now. Just a quick info to other readers. We were able to improve the load time in this case to around…
  • SEGGER - Nino -

    Replied to the thread Jlink RTT Viewer - Communication with other terminals.

    Post
    Hello, Thank you for your inquiry. You can gather RTT data with any client that uses telnet: segger.com/products/debug-prob…about-real-time-transfer/ See section RTT Communication. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread Cannot see all tasks, that are sent.

    Post
    Hello, Thank you for your inquiry. A guide on how to instrument NoOS applications can be found on our Wiki: wiki.segger.com/Use_SystemView_without_RTOS Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread Option to specify J-Link ProjectFile.

    Post
    Hello, It is currently no possible to set a JLink settings file in SystemView or a JLinkScript file. In the next release version of SystemView it is planned to have a CL option to set a specific JLinkScript file. To set a J-Link log file you can do so…
  • SEGGER - Schoenen -

    Replied to the thread Draw jpeg over widgets.

    Post
    Hi, As stated in the emWin user manual the approximate RAM requirement for displaying a JPEG is calculated as follows: App. RAM requirement = X-Size of image * 80 bytes + 33 Kbytes This depends on the compression type of the JPEG. Please refer to the…
  • SEGGER - Nino -

    Replied to the thread MX8 support.

    Post
    Hello, Thank you for your inquiry. The iMX8 is currently not officially supported by J-Link, it is not coupled to the Embedded Studio version. So it won't help going the IAR route as they depend on our official support as well. Current estimate for…
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Unable to download SES for Linux.

    Post
    Hi, OK thank you for confirmation. This thread will be closed now. Best regards, Nino
  • SEGGER - Nino -

    Replied to the thread [SOLVED] Nordic SES and mbedTLS with Zephyr.

    Post
    Hello David, Thank you for your inquiry. Zephyr and mbedTLS support is not provided by Segger. We recommend contacting Nordic in this regard. From the error message it seems that the macro MBEDTLS_CONFIG_FILE is not defined. You could try defining this…
  • SEGGER - Nino -

    Replied to the thread Is there a possibility for binding widget / GUI toolkit with SES?.

    Post
    Hello, Thank you for your inquiry. Such a possibility is currently not available with SES. But you could check out the nRF Connect for Desktop Tool from Nordic Semi. This should bring the capabilities you are looking for. Best regards, Nino