Recent Activities

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • bpeavey -

    Posted the thread svd file for STM32WB55.

    Thread
    Hi, I'm using Ozone with a J-Link probe to connect to a STM32WB55 Nucleo board. For other Nucleo boards, I have been able to search online for the appropriate .svd file to use for my target MCU. However, I'm unable to find a svd file for the…
  • boydy -

    Posted the thread BMP Slow to render unless layer rotation is set.

    Thread
    Hi I am rapidly learning my way through the emWIN system, with good results so far. I am using a STM32F7 device running at 216MHz, with a 320,240 RGB888 display on the integrated LTDC. The system is set up as a COLOR_MODE_RGB888 with only 1 layer. I…
  • Achim O. -

    Posted the thread SES 4.20a: g++ compiler error from "offsetof".

    Thread
    Hello, I am evaluating SES 4.20a. I had a similar issue some weeks ago with SES 4.18 but didn't investigate further because there was no free time then. Trying to compile the following source code: C Source Code (20 lines) I get this from the…
  • wittich -

    Replied to the thread program Cortex-M4 processor with 2 Xilinx FPGAs in JTAG chain.

    Post
    Hi, so if no one has any suggestions, can anyone give me more generic advice or experience with the combination of a JTAG chain of ARM (non-Zynq) + FPGA using SEGGER tools? Any hints or comments would be appreciated. Even an appropriate eval board I…
  • LexaGb -

    Replied to the thread LISTWHEEL background loses transparency.

    Post
    Yes, GUI_MAKE_COLOR is doing its job, but if I assign the ARGB-image to the IMAGE widget then the image in GUIBuilder looks like red and blue are swapped :) . Alex.
  • gaurav -

    Replied to the thread Extra background color length.

    Post
    I am attaching font converter. Please check. When you run .exe file it will open. One pop up window will come whatever default settings are there use same settings. Font Verdana Font Size 35 Save this file as a .c file. Regards Gaurav
  • SEGGER - Schoenen -

    Replied to the thread LISTWHEEL background loses transparency.

    Post
    Hi, the GUIBuilder should wrap color values with a macro like: GUI_MAKE_COLOR(0x000000FF) // Red This macor converts the given ABGR value into the proper byte order. Regards, Sven
  • awneil -

    Replied to the thread Extra background color length.

    Post
    There are many "font converters" on the internet - which one, specifically, did you use? Give a link.
  • volodymyr -

    Replied to the thread WM_SetUntouchable.

    Post
    Quote from SEGGER - Schoenen: “Hi, OK, now I got it, I guess. Try this: In WM_INIT_DIALOG of _cbDerivedDialog() I create another window which is transparent. This window will catch the input outside _cbDerivedDialog() and do nothing with it. After…
  • st0ne -

    Replied to the thread Some Keys not working correctly with NEO2 Keyboard Layout.

    Post
    Hi, ok, i have solved the problem now and write here if others have the same problem. I talked to neo2 guys in IRC and the problem here is with QT. So the problem should exist on other QT apps as well. The solution is to use the QUERTZ driver and…
  • LexaGb -

    Replied to the thread LISTWHEEL background loses transparency.

    Post
    Ok, Sven, thanks for clarifying, but one thing stops me from using ARGB. It is GUIBuilder that works in ABGR mode :) . So the colors look incorrectly. I got used to it for creating dialogs. Alex.
  • gaurav -

    Replied to the thread Extra background color length.

    Post
    Hi, I am sending .c file of verdana font and GUI.h file. Font converter is freely available on internet. You can download from there. Regards Gaurav
  • SEGGER - Schoenen -

    Replied to the thread LISTWHEEL background loses transparency.

    Post
    Hi, I think this is related to GUI_EnableAlpha(). Between V5.44 and V5.50 where some changes regarding the alpha module and this behavior should be fixed. Unfortunately, there is not much you can do about it, except of using a memory device or a bitmap…
  • LexaGb -

    Replied to the thread LISTWHEEL background loses transparency.

    Post
    Hello, Sven, This appears in simulation v5.44 (GUISim.lib from SEGGER package) and on real hardware using STemWin v5.44 (STemWin_CM7_wc32_ot.a from ST package). I'm using ABGR mode (GUI_USE_ARGB is set to 0) so we don't need to clear "alpha byte" of…
  • SEGGER - Schoenen -

    Replied to the thread WM_SetUntouchable.

    Post
    Hi, OK, now I got it, I guess. Try this: C Source Code (151 lines) In WM_INIT_DIALOG of _cbDerivedDialog() I create another window which is transparent. This window will catch the input outside _cbDerivedDialog() and do nothing with it. After…
  • SEGGER - Schoenen -

    Replied to the thread LISTWHEEL background loses transparency.

    Post
    Hi, I changed the line for setting the color in _LISTWHEEL_Draw() into C Source Code (1 line)and it is working. Depending on the color format emWin uses internally, the alpha bits can be 0x00 or 0xFF for opaque. If the library is compiled with…
  • SEGGER - Schoenen -

    Replied to the thread Extra background color length.

    Post
    Hi, I can't say if this is related to the font. I don't have the font. Is it possible to send me the font? If this is a free font, where can I download it? Regards, Sven
  • SEGGER - Schoenen -

    Replied to the thread Extra background color length.

    Post
    Hi, please don't open threads with the same topic/question multiple times. Regards, Sven
  • gaurav -

    Posted the thread Extra background color length.

    Thread
    Hi, I am using functions given below to display a string with background color. I want background color length corresponding to string length but in the end of string some extra length ( 1 character) of background color is coming. Please suggest…
  • awneil -

    Replied to the thread Request; STemwin Template for STM32H743ZI.

    Post
    Quote from CodesMagic: “It would be great if related script for STemwin be added to the configurator IDE (STM32CubeMX) ” CubeMX is ST's Product - not Segger - so you'd probably have to speak to ST about that ...