Recent Activities

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • nishantp -

    Posted the thread openocd via jlnik for cortexM0+..

    Thread
    Hi, Kindly let me know if I can flash cortexM0+ based controller using jlink via openocd software as I'm having ATSAMD21E16BU.
  • DenisCollis -

    Replied to the thread Cannot program QSPI Flash on NXP MK81FN256xxx15.

    Post
    FIXED. V6.44a Release Notes: 5. DLL: QSPI flash programming support for Freescale K80/K82 series devices, fixed.
  • DenisCollis -

    Posted the thread Cannot program QSPI Flash on NXP MK81FN256xxx15.

    Thread
    I have an NXP Kinetis K81 with QSPI XiP Flash. Code sections exist on both internal and external flash. Firmware loads and runs perfectly with the J-Link under control of NXP's Eclipse-based MCUXpresso IDE. However, when the IDE is not available, and…
  • dvescovi -

    Posted the thread MX8 support.

    Thread
    Is there a clear ETA as to when i.MX8 M4 support is going to be available? I was able to add J-link support by modifying the JLinkDevices.xml file and using the devices patch files from the NXP site. Unfortunately it does not look like it gets me all…
  • I have a J-Link EDU Mini. I cas succesfully program different STM32 MCU (F446 and F746) on the same JTAG bus as well as debug them at the same time. My question is now : is it possible to program multiple MCU at the same time in order to save some time.…
  • PaoloCazzola -

    Posted the thread STM32L072 reset when attaching to running program.

    Thread
    With STM32L0xx devices the "Attach to running program" procedure causes an unwanted reset of the device: Debug.SetConnectMode (CM_ATTACH); Exec.Connect(); Device "STM32L072CZ" selected. Found SW-DP with ID 0x0BC11477 Found SW-DP with ID…
  • jev -

    Replied to the thread Unable to download SES for Linux.

    Post
    This issue has disappeared after an hour or so. Must've been a hickup.
  • dsula -

    Replied to the thread can't connect to Syntacore SCR1.

    Post
    I've taken up this issue with Syntacore and according to them J-Link is NOT compatible with SCR1 (as of March 2019). The only supported option is to use OpenOCD.
  • SEGGER - Schoenen -

    Replied to the thread Prevent button getting focus.

    Post
    Hi, Yes, simply call BUTTON_SetFocusable(hButton, State) where hButton is a handle to the button and State describes whether it is focusable or not. Please note, that there was a typo in older versions of emWin. Depending on the version you are using…
  • mati1485 -

    Posted the thread Prevent button getting focus.

    Thread
    HI! I have several buttons that works like a switches. On first click button changes the variable state to true and second to false (for example). Everyting works perfect but there is a problem. When I click button first time it's get focus and second…
  • HenryGab -

    Posted the thread Telink single-wire support?.

    Thread
    Simple question. I've a number of devices that are now using the Telink TLSR8266 chipset, due to low cost BLE mesh support. This appears to use a proprietary singe-wire connection for programming (details are hard to come by). I've found an SDK to…
  • SEGGER - Nino -

    Replied to the thread Unable to download SES for Linux.

    Post
    Hello, Thank you for your inquiry. Such an issue is not known to us ES for Linux is of course still available. Could you provide a screenshot of the "old" looking website? Does it help when clearing browser cache and revisiting the site? Best…
  • jev -

    Posted the thread Unable to download SES for Linux.

    Thread
    Trying to download SES for ARM for a Linux host (either 32- or 64-bit) from segger.com/downloads/embedded-studio. Both (32-bit and 64-bit) versions don't start a download but send me to an old-looking download page. Is SES for Linux not available…
  • krzysztofnp -

    Posted the thread Cannot see all tasks, that are sent.

    Thread
    Hello, I'm trying to launch System View on our specific system and because of that, I use "NoOS" System View distrubution. I have 20 tasks, but SystemView displays only three channels. My tasks are displayed simultaneously within these three channels -…
  • nicastellanos -

    Posted the thread Ozone Breakpoints not setting correctly.

    Thread
    Hi there, I am using Ozone V2.60k along with an NXP Mk64F12 MCU. I have noticed that recently when I was debugging my code would begin running when I am stepping over through an IF/ELSE statement or a SWITCH case, basically anything with a conditional…
  • SEGGER - Schoenen -

    Replied to the thread Button background.

    Post
    Hi, yes, you can set a custom skinning routine. Attached is the example from my previous post but with an additional button. For this button I use a custom skinning routine which draws the bitmap. If clicked the button gets also a red…
  • davidra7 -

    Posted the thread Nordic SES and mbedTLS with Zephyr.

    Thread
    HI, I am developing software in SES V4.14 Nordic version (downloaded using NRF connect) for Nordic NRF9160 DK and everything works great until I tried to add mbedTLS. Nordic sample uses Zephyr framework and works great , I tried to add mbedTLS by adding…
  • doubleo.cbh -

    Posted the thread Is there a possibility for binding widget / GUI toolkit with SES?.

    Thread
    Hi all, I am currently researching Bluetooth Mesh with Nordic Thingy 52 (device) as my nodes. I use the mesh demo from Nordic and edit the codes using the environment of Segger Embedded Studio. I hope to create a GUI to show the observers how the…
  • anuj.tanksali -

    Replied to the thread Button background.

    Post
    Hello, Thanks is there any way if i don't want to override the callback function of button. Regards, Anuj
  • i was using the false version of Segger SystemView app, the bug in app has been fixed as discussed in https://forum.segger.com/index.php/Thread/3901-Bugs-found-in-SystemView