Recent Activities

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • shaddock -

    Posted the thread Downloading to SM470R1B1M with J-Link Pro.

    Thread
    I am trying to download c code to a SM470R1B1M-HT MCU using IAR Workbench and J-link Pro with a TC2050-IDC cable. When connected the middle LED and LED next to the return arrow are green. When downloading the two LEDs next to the direction arrows blink…
  • Andrzej -

    Replied to the thread STM32F746G-Discovery.

    Post
    What is the difference between _cbButton and cbButton?
  • SEGGER - Fabian -

    Replied to the thread How to set JLink to never power the board.

    Post
    Hi, Thank you for confirmation. From your description it is highly likely that your EDU was damaged from the USB side. This could have multiple reasons (e.g. resistors burned, faulty USB power supply). In that case the J-Link would need to be…
  • SilentDawn -

    Posted the thread Does STRACE functionality must halt?.

    Thread
    Hello Sir/Madam, We're trying to develop a tool based on the ETM and STRACE functionality of J-Trace SDK. We want to read the instructions flow infinitely real time. When I read the manual, I found that the section Simple Instruction Trace API (STRACE)…
  • SEGGER - Fabian -

    Replied to the thread Reflashing st-link doesn't work.

    Post
    Hi, Thank you for your inquiry. Could you provide us with the name of the eval board you are using? Are you using the newest SEGGER STLinkReflash tool? Are you using the newest J-Link Software and Documentation Pack?
  • Hi, Thank you for your inquiry. JTAG supports daisy chaining multiple cores that can then be debugged. Please find all necessary information about this here: wiki.segger.com/Manual_setup_of_JTAG_chain Best regards, Fabian
  • SEGGER - Florian -

    Replied to the thread emwin - GUI_LANG_LoadCSVEx loading different CSV files.

    Post
    Hi, I couldn't reproduce the error with this version either. Based on how your test went, it sounds like a memory issue. But in my test, emWin didn't run out of memory. You could still check if you run out of memory by watching the variable…
  • SEGGER - Fabian -

    Replied to the thread JLinkSWOViewer does not work with STM32WB55.

    Post
    Hi Fabien, We will give it a try at our side as soon as we find a time slot for this (Sometime this week). I will keep you posted. Best regards, Fabian
  • SEGGER - Fabian -

    Replied to the thread stm32g431 J-Link error "Failed to measure CPU clock frequency".

    Post
    Hi Pawel, Thank you for your inquiry. Such an issue is not known to us. Could you give us a step-by-step explanation on how to reproduce this issue? Best regards, Fabian
  • SEGGER - Florian -

    Replied to the thread Snapping time in a window motion.

    Post
    Hi Alex, I don't think it'll be easy to implement the LISTWHEEL's behavior into your custom widget. When the LISTWHEEL was made, there was no motion support but only timers (ancient times...). Also, as you already said, you can only set the Period in…
  • Sysmop226 -

    Replied to the thread emwin - GUI_LANG_LoadCSVEx loading different CSV files.

    Post
    Hi, This is the version. Source Code (1 line) I'm afraid I cannot send the application and the CSV files. But I started to suspect that the library does not clean the resources. Test scenario 1: I have a big CSV file (60k) when trying to load it twice it…
  • SEGGER - Fabian -

    Replied to the thread Not able to load binary file into Flash - ADuCM362.

    Post
    Hi Manjunath, Thank you for your inquiry. Such an issue is not known to us. 1) Could you please provide us with the full log output of J-Flash? 2) Could you please send us a J-Link log file? How to enable:
  • SEGGER - Schoenen -

    Replied to the thread Window.

    Post
    Hi, Below is a very basic example which shows how to create and delete a window on button press (or in this case on button release). C Source Code (117 lines)Regards, Sven
  • SEGGER - Fabian -

    Replied to the thread ST-Link reflash issues.

    Post
    Hi Alex, Thank you for your Inquiry. Such an issue is not known to us. We will try to reproduce this issue. Question: Could you provide us with reproduction steps for this issue? Best regards, Fabian
  • SEGGER - Fabian -

    Replied to the thread How to access multiple RTT channels from Telnet.

    Post
    Hi woody, Thank you for your inquiry. Please note that our TELNET implementation does not support other channels besides channel 0 yet. We will probably add this feature sometime in the future. To be able to use other channels, you would need to use…
  • htsmith19 -

    Replied to the thread DropDown Widget Problems.

    Post
    Hi Florian, Thanks for your help. I changed the List Height of the Dropdown widget to (Font Size * Number of Items + 2) and this has fixed my issue. Thanks, Henry
  • SEGGER - Fabian -

    Replied to the thread Ozone Feature Request: Telnet ports for additional RTT channels.

    Post
    Hi, Thank you for your inquiry and sorry for the delay in response. Quote from thomask77: “Bonus question: When you say "telnet", do you really mean TELNET according to RFC 854? ” We are opening a raw TCP Socket. Quote from thomask77: “It would…
  • bio_med -

    Posted the thread Window.

    Thread
    Hi, I would like to display a separate window after the button press. Is there a reference code for such functionality? I have gone through some sample codes provided by emWin but couldn't find anything that matched what I need. Thank you so much in…
  • SEGGER - Fabian -

    Replied to the thread OZone crash when new hex file is created.

    Post
    Hi, Thank you for your inquiry. Such an issue is not known to us. Does this problem still persist with the newest version of Ozone? If yes, could you provide us with a step-by-step explanation on how to reproduce this issue? Best regards, Fabian
  • SEGGER - Florian -

    Replied to the thread DropDown Widget Problems.

    Post
    Hi htsmith19, normally this happens if the y-size of the widget isn't big enough to display all the items. When this is the case, a white space is added to make up for that. And when this white space is clicked, the items move up. Note that the y-size…