Application log started - J-Flash V8.10b (J-Flash compiled Oct 9 2024 15:10:22) - JLinkARM.dll V8.10b (DLL compiled Oct 9 2024 15:09:50) Reading flash device list [C:\Program Files\SEGGER\Flasher_V810b\ETC/JFlash/Flash.csv] ... - List of flash devices read successfully (451 Devices) Reading MCU device list ... - List of MCU devices read successfully (11459 Devices) Opening project file [C:\myWork\T2GWorkFlashTest\T2GDownload.jflash] ... - Project opened successfully Opening data file [C:\myWork\T2GWorkFlashTest\T2GTest1_WorkFlashAll0xFF.srec] ... - Data file opened successfully (1212416 bytes, 2 ranges, CRC of data = 0x0ADA0CA7, CRC of file = 0x6505819D) Auto programming target (1212416 bytes, 2 ranges) ... - Connecting ... - Connecting via USB to probe/ programmer device 0 - Probe/ Programmer firmware: J-Link ARM / Flasher ARM V4 compiled Jun 15 2022 11:03:00 - Probe/ Programmer S/N: 164210485 - Device "CYT2B73CAD_M0" selected. - Target interface speed: 4000 kHz (Fixed) - VTarget = 4.903V - ConfigTargetSettings() start - Disabling optimizations: - Compare - SkipBlankDataOnProg - Flash breakpoints - ConfigTargetSettings() end - Took 75us - Found SW-DP with ID 0x6BA02477 - DPIDR: 0x6BA02477 - CoreSight SoC-400 or earlier - AP map detection skipped. Manually configured AP map found. - AP[0]: APB-AP (IDR: Not set, ADDR: 0x00000000) - AP[1]: AHB-AP (IDR: Not set, ADDR: 0x00000000) - AP[2]: AHB-AP (IDR: Not set, ADDR: 0x00000000) - AP[1]: Core found - AP[1]: AHB-AP ROM base: 0xF0000000 - CPUID register: 0x410CC601. Implementer code: 0x41 (ARM) - Found Cortex-M0 r0p1, Little endian. - FPUnit: 4 code (BP) slots and 0 literal slots - CoreSight components: - ROMTbl[0] @ F0000000 - [0][0]: E00FF000 CID B105100D PID 000BB4C0 ROM Table - ROMTbl[1] @ E00FF000 - [1][0]: E000E000 CID B105E00D PID 000BB008 SCS - [1][1]: E0001000 CID B105E00D PID 000BB00A DWT - [1][2]: E0002000 CID B105E00D PID 000BB00B FPB - [0][1]: F0002000 CID B105900D PID 000BB9A6 ??? - [0][2]: F0003000 CID B105900D PID 001BB932 MTB-M0+ - Executing init sequence ... - Executing Reset (0, 0 ms) - Reset type: NORMAL (https://wiki.segger.com/J-Link_Reset_Strategies) - Reset: Halt core after reset via DEMCR.VC_CORERESET. - Reset: Reset device via AIRCR.SYSRESETREQ. - Initialized successfully - Target interface speed: 4000 kHz (Fixed) - Found 1 JTAG device. Core ID: 0x6BA02477 (None) - Connected successfully - Checking if selected data fits into selected flash sectors. - Start of determining flash info (Bank 0 @ 0x10000000) - End of determining flash info - Flash bank info: - 30 * 32 KB @ 0x10000000 - 16 * 8 KB @ 0x10000000 - Start of preparing flash programming - Memory map 'after startup completion point' is active - End of preparing flash programming - Start of determining dirty areas in flash cache - End of determining dirty areas - CPU speed could not be measured. - Start of erasing sectors - Blank checking 0x10000000 - 0x1001FFFF - Erasing range 0x10000000 - 0x1001FFFF ( 4 Sectors, 128 KB) - Blank checking 0x10020000 - 0x1003FFFF - Blank checking 0x10040000 - 0x1005FFFF - Blank checking 0x10060000 - 0x1007FFFF - Blank checking 0x10080000 - 0x1009FFFF - Erasing range 0x10080000 - 0x1009FFFF ( 4 Sectors, 128 KB) - Blank checking 0x100A0000 - 0x100BFFFF - Blank checking 0x100C0000 - 0x100DFFFF - Blank checking 0x100E0000 - 0x100EFFFF - Blank checking 0x100F0000 - 0x1010FFFF - End of erasing sectors - Start of flash programming - Programming range 0x10000000 - 0x10007FFF ( 1 Sector, 32 KB) - Programming range 0x10008000 - 0x1000FFFF ( 1 Sector, 32 KB) - Programming range 0x10010000 - 0x10017FFF ( 1 Sector, 32 KB) - Programming range 0x10018000 - 0x1001FFFF ( 1 Sector, 32 KB) - Programming range 0x10020000 - 0x10027FFF ( 1 Sector, 32 KB) - Programming range 0x10028000 - 0x1002FFFF ( 1 Sector, 32 KB) - Programming range 0x10030000 - 0x10037FFF ( 1 Sector, 32 KB) - Programming range 0x10038000 - 0x1003FFFF ( 1 Sector, 32 KB) - Programming range 0x10040000 - 0x10047FFF ( 1 Sector, 32 KB) - Programming range 0x10048000 - 0x1004FFFF ( 1 Sector, 32 KB) - Programming range 0x10050000 - 0x10057FFF ( 1 Sector, 32 KB) - Programming range 0x10058000 - 0x1005FFFF ( 1 Sector, 32 KB) - Programming range 0x10060000 - 0x10067FFF ( 1 Sector, 32 KB) - Programming range 0x10068000 - 0x1006FFFF ( 1 Sector, 32 KB) - Programming range 0x10070000 - 0x10077FFF ( 1 Sector, 32 KB) - Programming range 0x10078000 - 0x1007FFFF ( 1 Sector, 32 KB) - Programming range 0x10080000 - 0x10087FFF ( 1 Sector, 32 KB) - Programming range 0x10088000 - 0x1008FFFF ( 1 Sector, 32 KB) - Programming range 0x10090000 - 0x10097FFF ( 1 Sector, 32 KB) - Programming range 0x10098000 - 0x1009FFFF ( 1 Sector, 32 KB) - Programming range 0x100A0000 - 0x100A7FFF ( 1 Sector, 32 KB) - Programming range 0x100A8000 - 0x100AFFFF ( 1 Sector, 32 KB) - Programming range 0x100B0000 - 0x100B7FFF ( 1 Sector, 32 KB) - Programming range 0x100B8000 - 0x100BFFFF ( 1 Sector, 32 KB) - Programming range 0x100C0000 - 0x100C7FFF ( 1 Sector, 32 KB) - Programming range 0x100C8000 - 0x100CFFFF ( 1 Sector, 32 KB) - Programming range 0x100D0000 - 0x100D7FFF ( 1 Sector, 32 KB) - Programming range 0x100D8000 - 0x100DFFFF ( 1 Sector, 32 KB) - Programming range 0x100E0000 - 0x100E7FFF ( 1 Sector, 32 KB) - Programming range 0x100E8000 - 0x100EFFFF ( 1 Sector, 32 KB) - Programming range 0x100F0000 - 0x100F7FFF ( 4 Sectors, 32 KB) - Programming range 0x100F8000 - 0x100FFFFF ( 4 Sectors, 32 KB) - Programming range 0x10100000 - 0x10107FFF ( 4 Sectors, 32 KB) - Programming range 0x10108000 - 0x1010FFFF ( 4 Sectors, 32 KB) - End of flash programming - Flash programming performed for 2 ranges (1114112 bytes) - 0x10000000 - 0x100EFFFF ( 30 Sectors, 960 KB) - 0x100F0000 - 0x1010FFFF ( 16 Sectors, 128 KB) - Start of verifying flash - End of verifying flash - Start of restoring - End of restoring - Start of determining flash info (Bank 1 @ 0x14000000) - End of determining flash info - Flash bank info: - 36 * 2 KB @ 0x14000000 - 192 * 128 bytes @ 0x14000000 - Start of preparing flash programming - End of preparing flash programming - Start of determining dirty areas in flash cache - End of determining dirty areas - CPU speed could not be measured. - Start of erasing sectors - Blank checking 0x14000000 - 0x14011FFF - Erasing range 0x14000000 - 0x14011FFF ( 36 Sectors, 72 KB) - Blank checking 0x14012000 - 0x14017FFF - Erasing range 0x14012000 - 0x14017FFF (192 Sectors, 24 KB) - End of erasing sectors - Start of flash programming - Programming range 0x14000000 - 0x14007FFF ( 16 Sectors, 32 KB) - Programming range 0x14008000 - 0x1400FFFF ( 16 Sectors, 32 KB) - Programming range 0x14010000 - 0x14011FFF ( 4 Sectors, 8 KB) - Programming range 0x14012000 - 0x14017FFF (192 Sectors, 24 KB) - End of flash programming - Flash programming performed for 2 ranges (98304 bytes) - 0x14000000 - 0x14011FFF ( 36 Sectors, 72 KB) - 0x14012000 - 0x14017FFF (192 Sectors, 24 KB) - Start of verifying flash - ERROR: Timeout while calculating CRC, RAMCode did not respond in time! - ERROR: Failed to read memory (0x10000 bytes @ address 0x14000000) - ERROR: Verification failed @ address 0x00000000 (CRC: 0x00000000, Expected: 0xBF655265) - End of verifying flash - ERROR: Verify failed - Start of restoring - End of restoring - ERROR: Failed to auto program target Disconnecting ... - Disconnected Opening data file [C:\myWork\T2GWorkFlashTest\T2GTest2_WorkFlashPart0xFF.srec] ... - Data file opened successfully (1212416 bytes, 2 ranges, CRC of data = 0x65EEACB3, CRC of file = 0x50D86A3D) Auto programming target (1212416 bytes, 2 ranges) ... - Connecting ... - Connecting via USB to probe/ programmer device 0 - Probe/ Programmer firmware: J-Link ARM / Flasher ARM V4 compiled Jun 15 2022 11:03:00 - Probe/ Programmer S/N: 164210485 - Device "CYT2B73CAD_M0" selected. - Target interface speed: 4000 kHz (Fixed) - VTarget = 4.896V - ConfigTargetSettings() start - Disabling optimizations: - Compare - SkipBlankDataOnProg - Flash breakpoints - ConfigTargetSettings() end - Took 421us - Found SW-DP with ID 0x6BA02477 - DPIDR: 0x6BA02477 - CoreSight SoC-400 or earlier - AP map detection skipped. Manually configured AP map found. - AP[0]: APB-AP (IDR: Not set, ADDR: 0x00000000) - AP[1]: AHB-AP (IDR: Not set, ADDR: 0x00000000) - AP[2]: AHB-AP (IDR: Not set, ADDR: 0x00000000) - AP[1]: Core found - AP[1]: AHB-AP ROM base: 0xF0000000 - CPUID register: 0x410CC601. Implementer code: 0x41 (ARM) - Found Cortex-M0 r0p1, Little endian. - FPUnit: 4 code (BP) slots and 0 literal slots - CoreSight components: - ROMTbl[0] @ F0000000 - [0][0]: E00FF000 CID B105100D PID 000BB4C0 ROM Table - ROMTbl[1] @ E00FF000 - [1][0]: E000E000 CID B105E00D PID 000BB008 SCS - [1][1]: E0001000 CID B105E00D PID 000BB00A DWT - [1][2]: E0002000 CID B105E00D PID 000BB00B FPB - [0][1]: F0002000 CID B105900D PID 000BB9A6 ??? - [0][2]: F0003000 CID B105900D PID 001BB932 MTB-M0+ - Executing init sequence ... - Executing Reset (0, 0 ms) - Reset type: NORMAL (https://wiki.segger.com/J-Link_Reset_Strategies) - Reset: Halt core after reset via DEMCR.VC_CORERESET. - Reset: Reset device via AIRCR.SYSRESETREQ. - Initialized successfully - Target interface speed: 4000 kHz (Fixed) - Found 1 JTAG device. Core ID: 0x6BA02477 (None) - Connected successfully - Checking if selected data fits into selected flash sectors. - Start of determining flash info (Bank 0 @ 0x10000000) - End of determining flash info - Flash bank info: - 30 * 32 KB @ 0x10000000 - 16 * 8 KB @ 0x10000000 - Start of preparing flash programming - Memory map 'after startup completion point' is active - End of preparing flash programming - Start of determining dirty areas in flash cache - End of determining dirty areas - CPU speed could not be measured. - Start of erasing sectors - Blank checking 0x10000000 - 0x1001FFFF - Erasing range 0x10000000 - 0x1001FFFF ( 4 Sectors, 128 KB) - Blank checking 0x10020000 - 0x1003FFFF - Blank checking 0x10040000 - 0x1005FFFF - Blank checking 0x10060000 - 0x1007FFFF - Blank checking 0x10080000 - 0x1009FFFF - Erasing range 0x10080000 - 0x1009FFFF ( 4 Sectors, 128 KB) - Blank checking 0x100A0000 - 0x100BFFFF - Blank checking 0x100C0000 - 0x100DFFFF - Blank checking 0x100E0000 - 0x100EFFFF - Blank checking 0x100F0000 - 0x1010FFFF - End of erasing sectors - Start of flash programming - Programming range 0x10000000 - 0x10007FFF ( 1 Sector, 32 KB) - Programming range 0x10008000 - 0x1000FFFF ( 1 Sector, 32 KB) - Programming range 0x10010000 - 0x10017FFF ( 1 Sector, 32 KB) - Programming range 0x10018000 - 0x1001FFFF ( 1 Sector, 32 KB) - Programming range 0x10020000 - 0x10027FFF ( 1 Sector, 32 KB) - Programming range 0x10028000 - 0x1002FFFF ( 1 Sector, 32 KB) - Programming range 0x10030000 - 0x10037FFF ( 1 Sector, 32 KB) - Programming range 0x10038000 - 0x1003FFFF ( 1 Sector, 32 KB) - Programming range 0x10040000 - 0x10047FFF ( 1 Sector, 32 KB) - Programming range 0x10048000 - 0x1004FFFF ( 1 Sector, 32 KB) - Programming range 0x10050000 - 0x10057FFF ( 1 Sector, 32 KB) - Programming range 0x10058000 - 0x1005FFFF ( 1 Sector, 32 KB) - Programming range 0x10060000 - 0x10067FFF ( 1 Sector, 32 KB) - Programming range 0x10068000 - 0x1006FFFF ( 1 Sector, 32 KB) - Programming range 0x10070000 - 0x10077FFF ( 1 Sector, 32 KB) - Programming range 0x10078000 - 0x1007FFFF ( 1 Sector, 32 KB) - Programming range 0x10080000 - 0x10087FFF ( 1 Sector, 32 KB) - Programming range 0x10088000 - 0x1008FFFF ( 1 Sector, 32 KB) - Programming range 0x10090000 - 0x10097FFF ( 1 Sector, 32 KB) - Programming range 0x10098000 - 0x1009FFFF ( 1 Sector, 32 KB) - Programming range 0x100A0000 - 0x100A7FFF ( 1 Sector, 32 KB) - Programming range 0x100A8000 - 0x100AFFFF ( 1 Sector, 32 KB) - Programming range 0x100B0000 - 0x100B7FFF ( 1 Sector, 32 KB) - Programming range 0x100B8000 - 0x100BFFFF ( 1 Sector, 32 KB) - Programming range 0x100C0000 - 0x100C7FFF ( 1 Sector, 32 KB) - Programming range 0x100C8000 - 0x100CFFFF ( 1 Sector, 32 KB) - Programming range 0x100D0000 - 0x100D7FFF ( 1 Sector, 32 KB) - Programming range 0x100D8000 - 0x100DFFFF ( 1 Sector, 32 KB) - Programming range 0x100E0000 - 0x100E7FFF ( 1 Sector, 32 KB) - Programming range 0x100E8000 - 0x100EFFFF ( 1 Sector, 32 KB) - Programming range 0x100F0000 - 0x100F7FFF ( 4 Sectors, 32 KB) - Programming range 0x100F8000 - 0x100FFFFF ( 4 Sectors, 32 KB) - Programming range 0x10100000 - 0x10107FFF ( 4 Sectors, 32 KB) - Programming range 0x10108000 - 0x1010FFFF ( 4 Sectors, 32 KB) - End of flash programming - Flash programming performed for 2 ranges (1114112 bytes) - 0x10000000 - 0x100EFFFF ( 30 Sectors, 960 KB) - 0x100F0000 - 0x1010FFFF ( 16 Sectors, 128 KB) - Start of verifying flash - End of verifying flash - Start of restoring - End of restoring - Start of determining flash info (Bank 1 @ 0x14000000) - End of determining flash info - Flash bank info: - 36 * 2 KB @ 0x14000000 - 192 * 128 bytes @ 0x14000000 - Start of preparing flash programming - End of preparing flash programming - Start of determining dirty areas in flash cache - End of determining dirty areas - CPU speed could not be measured. - Start of erasing sectors - Blank checking 0x14000000 - 0x14011FFF - Erasing range 0x14000000 - 0x14011FFF ( 36 Sectors, 72 KB) - Blank checking 0x14012000 - 0x14017FFF - Erasing range 0x14012000 - 0x14017FFF (192 Sectors, 24 KB) - End of erasing sectors - Start of flash programming - Programming range 0x14000000 - 0x14007FFF ( 16 Sectors, 32 KB) - Programming range 0x14008000 - 0x1400FFFF ( 16 Sectors, 32 KB) - Programming range 0x14010000 - 0x14011FFF ( 4 Sectors, 8 KB) - Programming range 0x14012000 - 0x14017FFF (192 Sectors, 24 KB) - End of flash programming - Flash programming performed for 2 ranges (98304 bytes) - 0x14000000 - 0x14011FFF ( 36 Sectors, 72 KB) - 0x14012000 - 0x14017FFF (192 Sectors, 24 KB) - Start of verifying flash - ERROR: Timeout while calculating CRC, RAMCode did not respond in time! - ERROR: Failed to read memory (0x2000 bytes @ address 0x14010000) - ERROR: Verification failed @ address 0x00000000 (CRC: 0xC02C91E0, Expected: 0xEE742AAB) - End of verifying flash - ERROR: Verify failed - Start of restoring - End of restoring - ERROR: Failed to auto program target Disconnecting ... - Disconnected Close project - Project closed