SEGGER J-Link Commander V7.94 (Compiled Nov 29 2023 13:43:12)
DLL version V7.94, compiled Nov 29 2023 13:41:24

J-Link Commander will now exit on Error
Connecting to J-Link via USB...O.K.
Firmware: J-Link V11 compiled Nov 22 2023 09:48:47
Hardware version: V11.00
J-Link uptime (since boot): 0d 00h 27m 33s
S/N: 851000087
License(s): RDI, FlashBP, FlashDL, JFlash, GDB
USB speed mode: High speed (480 MBit/s)
VTref=3.328V
Device "STM32G474VC" selected.


Connecting to target via SWD
InitTarget() start
SWD selected. Executing JTAG -> SWD switching sequence.
DAP initialized successfully.
InitTarget() end - Took 15.4ms
Found SW-DP with ID 0x2BA01477
DPIDR: 0x2BA01477
CoreSight SoC-400 or earlier
Scanning AP map to find all available APs
AP[1]: Stopped AP scan as end of AP map has been reached
AP[0]: AHB-AP (IDR: 0x24770011)
Iterating through AP map to find AHB-AP to use
AP[0]: Core found
AP[0]: AHB-AP ROM base: 0xE00FF000
CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
Found Cortex-M4 r0p1, Little endian.
FPUnit: 6 code (BP) slots and 2 literal slots
CoreSight components:
ROMTbl[0] @ E00FF000
[0][0]: E000E000 CID B105E00D PID 000BB00C SCS-M7
[0][1]: E0001000 CID B105E00D PID 003BB002 DWT
[0][2]: E0002000 CID B105E00D PID 002BB003 FPB
[0][3]: E0000000 CID B105E00D PID 003BB001 ITM
[0][4]: E0040000 CID B105900D PID 000BB9A1 TPIU
[0][5]: E0041000 CID B105900D PID 000BB925 ETM
Memory zones:
  Zone: "Default" Description: Default access mode
Cortex-M4 identified.
J-Link>No address range specified, 'Erase Chip' will be executed
'erase': Performing implicit reset & halt of MCU.
Reset: Halt core after reset via DEMCR.VC_CORERESET.
Reset: Reset device via AIRCR.SYSRESETREQ.
Erasing device...
J-Link: Flash download: Total time needed: 0.269s (Prepare: 0.134s, Compare: 0.000s, Erase: 0.060s, Program: 0.000s, Verify: 0.000s, Restore: 0.074s)
J-Link: Flash download: Total time needed: 0.100s (Prepare: 0.053s, Compare: 0.000s, Erase: 0.024s, Program: 0.000s, Verify: 0.000s, Restore: 0.022s)
J-Link: Flash download: Total time needed: 0.090s (Prepare: 0.049s, Compare: 0.000s, Erase: 0.018s, Program: 0.000s, Verify: 0.000s, Restore: 0.023s)
Erasing done.
J-Link>Reset delay: 0 ms
Reset type NORMAL: Resets core & peripherals via SYSRESETREQ & VECTRESET bit.
Reset: Halt core after reset via DEMCR.VC_CORERESET.
Reset: Reset device via AIRCR.SYSRESETREQ.
J-Link>J-Link>'loadfile': Performing implicit reset & halt of MCU.
Reset: Halt core after reset via DEMCR.VC_CORERESET.
Reset: Reset device via AIRCR.SYSRESETREQ.
Downloading file [build/release/app.hex]...
J-Link: Flash download: Bank 0 @ 0x08000000: 1 range affected (43008 bytes)
J-Link: Flash download: Total: 1.374s (Prepare: 0.094s, Compare: 0.091s, Erase: 0.481s, Program: 0.486s, Verify: 0.161s, Restore: 0.057s)
J-Link: Flash download: Program speed: 86 KB/s
O.K.
J-Link>Reset delay: 0 ms
Reset type NORMAL: Resets core & peripherals via SYSRESETREQ & VECTRESET bit.
Reset: Halt core after reset via DEMCR.VC_CORERESET.
Reset: Reset device via AIRCR.SYSRESETREQ.
J-Link>Memory map 'after startup completion point' is active
J-Link>OnDisconnectTarget() start
OnDisconnectTarget() end - Took 8.12ms