Auto programming target (76040 bytes, 2 ranges) ...
 - Connecting ...
  - Connecting via USB to probe/ programmer device 0
  - Probe/ Programmer firmware: J-Link / Flasher ARM V5-1 compiled May  8 2023 13:15:32
  - Probe/ Programmer S/N: 165105086
  - Device "R7FS5D97E" selected.
  - Target interface speed: 4000 kHz (Fixed)
  - VTarget = 3.052V
  - InitTarget() start
  - Identifying target device...
  - SWD selected. Executing JTAG -> SWD switching sequence...
  - Initializing DAP...
  - Low power mode detected. Waking device from low power mode.
  - InitTarget() end - Took 29.5ms
  - Found SW-DP with ID 0x5BA02477
  - DPIDR: 0x5BA02477
  - CoreSight SoC-400 or earlier
  - Scanning AP map to find all available APs
  - AP[2]: Stopped AP scan as end of AP map has been reached
  - AP[0]: AHB-AP (IDR: 0x24770011)
  - AP[1]: APB-AP (IDR: 0x44770002)
  - Iterating through AP map to find AHB-AP to use
  - AP[0]: Core found
  - AP[0]: AHB-AP ROM base: 0xE00FF000
  - CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
  - Found Cortex-M4 r0p1, Little endian.
  - FPUnit: 6 code (BP) slots and 2 literal slots
  - CoreSight components:
  - ROMTbl[0] @ E00FF000
  - [0][0]: E000E000 CID B105E00D PID 000BB00C SCS-M7
  - [0][1]: E0001000 CID B105E00D PID 003BB002 DWT
  - [0][2]: E0002000 CID B105E00D PID 002BB003 FPB
  - [0][3]: E0000000 CID B105E00D PID 003BB001 ITM
  - [0][4]: E0040000 CID B105900D PID 000BB9A1 TPIU
  - [0][5]: E0041000 CID B105900D PID 000BB925 ETM
  - [0][6]: E0042000 CID B105900D PID 002BB908 CSTF
  - [0][7]: E0043000 CID B105900D PID 001BB961 TMC
  - [0][8]: E0044000 CID B105F00D PID 001BB101 TSG
  - Executing init sequence ...
  - Target interface speed: 4000 kHz (Fixed)
  - CPU clock frequency: 1989 kHz (Auto detected)
  - Found 1 JTAG device. Core ID: 0x5BA02477 (None)
  - Connected successfully
 - Checking if selected data fits into selected flash sectors.
 - Start of preparing flash programming
 - End of preparing flash programming
 - Start of determining dirty areas in flash cache
 - End of determining dirty areas
 - CPU is running at 100000 kHz.
 - Start of erasing sectors
 - Blank checking 0x0100A150 - 0x0100A16F
 - End of erasing sectors
 - Start of flash programming
 - Programming range 0x0100A150 - 0x0100A16F (  1 Sector, 32 Bytes)
 - End of flash programming
 - Flash programming performed for 1 range (32 bytes)
 - 0x100A150 - 0x100A16F (  1 Sector, 32 Bytes)
 - Start of verifying flash
 - End of verifying flash
 - Start of restoring
 - End of restoring
 - Start of preparing flash programming
 - End of preparing flash programming
 - Start of determining dirty areas in flash cache
 - End of determining dirty areas
 - CPU is running at 100000 kHz.
 - Start of erasing sectors
 - Blank checking 0x00000000 - 0x0000FFFF
 - Erasing range 0x00000000 - 0x0000FFFF (  8 Sectors, 64 KB)
 - Blank checking 0x00010000 - 0x00017FFF
 - Erasing range 0x00010000 - 0x00017FFF (  1 Sector, 32 KB)
 - End of erasing sectors
 - Start of flash programming
 - Programming range 0x00000000 - 0x00007FFF (  4 Sectors, 32 KB)
 - Programming range 0x00008000 - 0x0000FFFF (  4 Sectors, 32 KB)
 - Programming range 0x00010000 - 0x00017FFF (  1 Sector, 32 KB)
 - End of flash programming
 - Flash programming performed for 2 ranges (98304 bytes)
 - 0x0000 - 0xFFFF (  8 Sectors, 64 KB)
 - 0x10000 - 0x17FFF (  1 Sector, 32 KB)
 - Start of verifying flash
 - End of verifying flash
 - Start of restoring
 - End of restoring
 - WARNING: Flash bank 3 disabled, skipped.
 - Executing exit sequence ...
  - De-initialized successfully
 - Target erased, programmed and verified successfully - Completed after 1.390 sec