Application log started
 - J-Flash V6.82d (J-Flash compiled Aug 13 2020 17:22:49)
 - JLinkARM.dll V6.82d (DLL compiled Aug 13 2020 17:22:18)
Optional command line parameters found
 - [1]: -USB601004224
 - [2]: -openprjC:\***\ProjectMCU.jflash
 - [3]: -openC:\***.hex
 - [4]: -jflashlogC:\Reports\SEGGER_LOGS\logMCU.txt
 - [5]: -connect
 - [6]: -auto
 - [7]: -disconnect
 - [8]: -exit
Reading flash device list [C:\Program Files (x86)\Segger\JLink_V682d\ETC/JFlash/Flash.csv] ...
 - List of flash devices read successfully (451 Devices)
Reading MCU device list ...
 - List of MCU devices read successfully (7837 Devices)
Opening project file [C:\***\ProjectMCU.jflash] ...
 - Project opened successfully
Opening data file [C:\***.hex] ...
 - Data file opened successfully (275457 bytes, 4 ranges, CRC of data = 0x7432ECD5, CRC of file = 0xFFDBCDA9)
Connecting ...
 - Connecting via USB to probe/ programmer with SN 601004224
 - Probe/ Programmer firmware: J-Link V11 compiled Jul 17 2020 16:24:07
 - Device "STM32F469NG" selected.
 - Target interface speed: 12000 kHz (Fixed)
 - VTarget = 3.341V
 - TotalIRLen = 9, IRPrint = 0x0011
 - JTAG chain detection found 2 devices:
 -  #0 Id: 0x4BA00477, IRLen: 04, CoreSight JTAG-DP
 -  #1 Id: 0x06434041, IRLen: 05, STM32 Boundary Scan
 - Device will be unsecured now.
 - TotalIRLen = 9, IRPrint = 0x0011
 - JTAG chain detection found 2 devices:
 -  #0 Id: 0x4BA00477, IRLen: 04, CoreSight JTAG-DP
 -  #1 Id: 0x06434041, IRLen: 05, STM32 Boundary Scan
 - Cannot determine DP version. Assuming DPv0
 - Scanning AP map to find all available APs
 - AP[1]: Stopped AP scan as end of AP map has been reached
 - AP[0]: AHB-AP (IDR: 0x24770011)
 - Iterating through AP map to find AHB-AP to use
 - AP[0]: Core found
 - AP[0]: AHB-AP ROM base: 0xE00FF000
 - CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
 - Found Cortex-M4 r0p1, Little endian.
 - FPUnit: 6 code (BP) slots and 2 literal slots
 - CoreSight components:
 - ROMTbl[0] @ E00FF000
 - ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7
 - ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT
 - ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB
 - ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM
 - ROMTbl[0][4]: E0040000, CID: B105900D, PID: 000BB9A1 TPIU
 - ROMTbl[0][5]: E0041000, CID: B105900D, PID: 000BB925 ETM
 - Executing init sequence ...
  - Initialized successfully
 - Target interface speed: 12000 kHz (Fixed)
 - Found 2 JTAG devices. Core ID: 0x4BA00477 (None)
 - Connected successfully
Auto programming target (275457 bytes, 4 ranges) ...
 - Checking if selected data fits into selected flash sectors.
 - Start of preparing flash programming
 - End of preparing flash programming
 - Start of determining dirty areas in flash cache
 - End of determining dirty areas
 - CPU is running at 110000 kHz.
 - Chip erase not supported for flash bank @ 0x08000000. Switched to sector erase
 - Start of determining dirty areas in flash cache
 - End of determining dirty areas
 - Start of erasing sectors
 - Blank checking 0x08000000 - 0x0800FFFF
 - Blank checking 0x08010000 - 0x0801FFFF
 - Blank checking 0x08020000 - 0x0803FFFF
 - Blank checking 0x08040000 - 0x0805FFFF
 - Blank checking 0x08060000 - 0x0807FFFF
 - Blank checking 0x08080000 - 0x0809FFFF
 - Blank checking 0x080A0000 - 0x080BFFFF
 - Blank checking 0x080C0000 - 0x080DFFFF
 - Blank checking 0x080E0000 - 0x080FFFFF
 - End of erasing sectors
 - Start of flash programming
 - Programming range 0x08000000 - 0x08007FFF (  2 Sectors, 32 KB)
 - Programming range 0x08010000 - 0x0801FFFF (  1 Sector, 64 KB)
 - Programming range 0x08020000 - 0x0803FFFF (  1 Sector, 128 KB)
 - Programming range 0x08040000 - 0x0805FFFF (  1 Sector, 128 KB)
 - Programming range 0x080E0000 - 0x080FFFFF (  1 Sector, 128 KB)
 - End of flash programming
 - Flash programming performed for 4 ranges (491520 bytes)
 - 0x8000000 - 0x8007FFF (  2 Sectors, 32 KB)
 - 0x8010000 - 0x801FFFF (  1 Sector, 64 KB)
 - 0x8020000 - 0x805FFFF (  2 Sectors, 256 KB)
 - 0x80E0000 - 0x80FFFFF (  1 Sector, 128 KB)
 - Start of verifying flash
 - End of verifying flash
 - Start of restoring
 - End of restoring
 - ERROR: Programming canceled by user
J-Flash V6.82d Error: Programming canceled by user
Disconnecting ...
 - Disconnected
Close project
 - Project closed