Auto programming target (88554 bytes, 5 ranges) ...
 - Connecting ...
    - Connecting via USB to J-Link device 0
    - J-Link firmware: J-Link / Flasher Portable Plus V1 compiled Feb 13 2020 16:15:24
    - Device "R7FS3A678" selected.
    - Target interface speed: 4000 kHz (Fixed)
    - VTarget = 3.298V
    - Found SW-DP with ID 0x5BA02477
    - Found SW-DP with ID 0x5BA02477
    - DPIDR: 0x5BA02477
    - Scanning AP map to find all available APs
    - AP[2]: Stopped AP scan as end of AP map has been reached
    - AP[0]: AHB-AP (IDR: 0x24770011)
    - AP[1]: APB-AP (IDR: 0x44770002)
    - Iterating through AP map to find AHB-AP to use
    - AP[0]: Core found
    - AP[0]: AHB-AP ROM base: 0xE00FF000
    - CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
    - Found Cortex-M4 r0p1, Little endian.
    - FPUnit: 6 code (BP) slots and 2 literal slots
    - CoreSight components:
    - ROMTbl[0] @ E00FF000
    - ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7
    - ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT
    - ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB
    - ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM
    - ROMTbl[0][4]: E0040000, CID: B105900D, PID: 000BB9A1 TPIU
    - ROMTbl[0][5]: E0041000, CID: B105900D, PID: 000BB925 ETM
    - ROMTbl[0][6]: E0042000, CID: B105900D, PID: 002BB908 CSTF
    - ROMTbl[0][7]: E0043000, CID: B105900D, PID: 001BB961 TMC
    - ROMTbl[0][8]: E0044000, CID: B105F00D, PID: 001BB101 TSG
    - Executing init sequence ...
       - Initialized successfully
    - Target interface speed: 4000 kHz (Fixed)
    - CPU clock frequency: 47982 kHz (Auto detected)
    - J-Link found 1 JTAG device. Core ID: 0x5BA02477 (None)
    - Connected successfully
 - Checking if selected data fits into selected flash sectors.
 - Start of preparing flash programming
 - End of preparing flash programming
 - Start of determining dirty areas in flash cache
 - End of determining dirty areas
 - CPU is running at 47985 kHz.
 - Chip erase not supported for flash bank @ 0x00000000. Switched to sector erase
 - Start of determining dirty areas in flash cache
 - End of determining dirty areas
 - Start of erasing sectors
 - Blank checking 0x00000000 - 0x0001FFFF
 - Blank checking 0x00020000 - 0x0003FFFF
 - Blank checking 0x01010008 - 0x01010033
 - Blank checking 0x40100000 - 0x40101FFF
 - End of erasing sectors
 - Start of flash programming
 - Programming range 0x00000000 - 0x00007FFF ( 16 Sectors, 32 KB)
 - Programming range 0x00008000 - 0x0000FFFF ( 16 Sectors, 32 KB)
 - Programming range 0x00010000 - 0x000157FF ( 11 Sectors, 22 KB)
 - Programming range 0x40100000 - 0x401007FF (  2 Sectors, 2 KB)
 - End of flash programming
 - Flash programming performed for 2 ranges (90112 bytes)
 - 0x0000 - 0x157FF ( 43 Sectors, 86 KB)
 - 0x40100000 - 0x401007FF (  2 Sectors, 2 KB)
 - Start of verifying flash
 - End of verifying flash
 - Start of restoring
 - End of restoring
 - Executing exit sequence ...
    - De-initialized successfully
 - Target erased, programmed and verified successfully - Completed after 1.640 sec
 - Starting application ...
    - Disconnecting ...
       - Disconnected
    - Connecting via USB to J-Link device 0
    - J-Link firmware: J-Link / Flasher Portable Plus V1 compiled Feb 13 2020 16:15:24
    - Device "R7FS3A678" selected.
    - Found SW-DP with ID 0x5BA02477
    - Found SW-DP with ID 0x5BA02477
    - DPIDR: 0x5BA02477
    - Scanning AP map to find all available APs
    - AP[2]: Stopped AP scan as end of AP map has been reached
    - AP[0]: AHB-AP (IDR: 0x24770011)
    - AP[1]: APB-AP (IDR: 0x44770002)
    - Iterating through AP map to find AHB-AP to use
    - AP[0]: Core found
    - AP[0]: AHB-AP ROM base: 0xE00FF000
    - CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
    - Found Cortex-M4 r0p1, Little endian.
    - FPUnit: 6 code (BP) slots and 2 literal slots
    - CoreSight components:
    - ROMTbl[0] @ E00FF000
    - ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7
    - ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT
    - ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB
    - ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM
    - ROMTbl[0][4]: E0040000, CID: B105900D, PID: 000BB9A1 TPIU
    - ROMTbl[0][5]: E0041000, CID: B105900D, PID: 000BB925 ETM
    - ROMTbl[0][6]: E0042000, CID: B105900D, PID: 002BB908 CSTF
    - ROMTbl[0][7]: E0043000, CID: B105900D, PID: 001BB961 TMC
    - ROMTbl[0][8]: E0044000, CID: B105F00D, PID: 001BB101 TSG
    - Reset: Halt core after reset via DEMCR.VC_CORERESET.
    - Reset: Reset device via AIRCR.SYSRESETREQ.
    - Target application started




Reading entire flash chip ...
 - Connecting ...
    - Connecting via USB to J-Link device 0
    - J-Link firmware: J-Link / Flasher Portable Plus V1 compiled Feb 13 2020 16:15:24
    - Device "R7FS3A678" selected.
    - Target interface speed: 4000 kHz (Fixed)
    - VTarget = 3.297V
    - Found SW-DP with ID 0x5BA02477
    - Found SW-DP with ID 0x5BA02477
    - DPIDR: 0x5BA02477
    - Scanning AP map to find all available APs
    - AP[2]: Stopped AP scan as end of AP map has been reached
    - AP[0]: AHB-AP (IDR: 0x24770011)
    - AP[1]: APB-AP (IDR: 0x44770002)
    - Iterating through AP map to find AHB-AP to use
    - AP[0]: Core found
    - AP[0]: AHB-AP ROM base: 0xE00FF000
    - CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
    - Found Cortex-M4 r0p1, Little endian.
    - FPUnit: 6 code (BP) slots and 2 literal slots
    - CoreSight components:
    - ROMTbl[0] @ E00FF000
    - ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7
    - ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT
    - ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB
    - ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM
    - ROMTbl[0][4]: E0040000, CID: B105900D, PID: 000BB9A1 TPIU
    - ROMTbl[0][5]: E0041000, CID: B105900D, PID: 000BB925 ETM
    - ROMTbl[0][6]: E0042000, CID: B105900D, PID: 002BB908 CSTF
    - ROMTbl[0][7]: E0043000, CID: B105900D, PID: 001BB961 TMC
    - ROMTbl[0][8]: E0044000, CID: B105F00D, PID: 001BB101 TSG
    - Executing init sequence ...
       - Initialized successfully
    - Target interface speed: 4000 kHz (Fixed)
    - CPU clock frequency: 47991 kHz (Auto detected)
    - J-Link found 1 JTAG device. Core ID: 0x5BA02477 (None)
    - Connected successfully
 - 137 sectors, 3 ranges, 0x0 - 0x3FFFF, 0x1010008 - 0x1010033, 0x40100000 - 0x40101FFF
 - Start of preparing flash programming
 - End of preparing flash programming
 - Blank checking 0x00000000 - 0x0001FFFF
 - Blank checking 0x00020000 - 0x0003FFFF
 - Blank checking 0x01010008 - 0x01010033
 - Blank checking 0x40100000 - 0x40101FFF
 - Start of restoring
 - End of restoring
 - Target memory read successfully. (270380 bytes, 3 ranges) - Completed after 1.301 sec



Erasing chip ...
 - 137 sectors, 3 ranges, 0x0 - 0x3FFFF, 0x1010008 - 0x1010033, 0x40100000 - 0x40101FFF
 - Start of preparing flash programming
 - End of preparing flash programming
 - Start of determining dirty areas in flash cache
 - End of determining dirty areas
 - CPU is running at 50125 kHz.
 - Chip erase not supported for flash bank @ 0x00000000. Switched to sector erase
 - Start of determining dirty areas in flash cache
 - End of determining dirty areas
 - Start of erasing sectors
 - Blank checking 0x00000000 - 0x0001FFFF
 - Erasing range 0x00000000 - 0x0001FFFF ( 64 Sectors, 128 KB)
 - Blank checking 0x00020000 - 0x0003FFFF
 - Blank checking 0x01010008 - 0x01010033
 - Blank checking 0x40100000 - 0x40101FFF
 - Erasing range 0x40100000 - 0x40101FFF (  8 Sectors, 8 KB)
 - End of erasing sectors
 - Start of restoring
 - End of restoring
 - Erase operation completed successfully - Completed after 0.520 sec



Reading entire flash chip ...
 - 137 sectors, 3 ranges, 0x0 - 0x3FFFF, 0x1010008 - 0x1010033, 0x40100000 - 0x40101FFF
 - Start of preparing flash programming
 - End of preparing flash programming
 - Blank checking 0x00000000 - 0x0001FFFF
 - Blank checking 0x00020000 - 0x0003FFFF
 - Blank checking 0x01010008 - 0x01010033
 - Blank checking 0x40100000 - 0x40101FFF
 - Start of restoring
 - End of restoring
 - Target memory read successfully. (270380 bytes, 3 ranges) - Completed after 0.300 sec
 
 
Disconnecting ...
 - Disconnected



Auto programming target (88554 bytes, 5 ranges) ...
 - Connecting ...
    - Connecting via USB to J-Link device 0
    - J-Link firmware: J-Link / Flasher Portable Plus V1 compiled Feb 13 2020 16:15:24
    - Device "R7FS3A678" selected.
    - Target interface speed: 4000 kHz (Fixed)
    - VTarget = 3.297V
    - Found SW-DP with ID 0x5BA02477
    - Found SW-DP with ID 0x5BA02477
    - DPIDR: 0x5BA02477
    - Scanning AP map to find all available APs
    - AP[2]: Stopped AP scan as end of AP map has been reached
    - AP[0]: AHB-AP (IDR: 0x24770011)
    - AP[1]: APB-AP (IDR: 0x44770002)
    - Iterating through AP map to find AHB-AP to use
    - AP[0]: Core found
    - AP[0]: AHB-AP ROM base: 0xE00FF000
    - CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
    - Found Cortex-M4 r0p1, Little endian.
    - FPUnit: 6 code (BP) slots and 2 literal slots
    - CoreSight components:
    - ROMTbl[0] @ E00FF000
    - ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7
    - ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT
    - ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB
    - ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM
    - ROMTbl[0][4]: E0040000, CID: B105900D, PID: 000BB9A1 TPIU
    - ROMTbl[0][5]: E0041000, CID: B105900D, PID: 000BB925 ETM
    - ROMTbl[0][6]: E0042000, CID: B105900D, PID: 002BB908 CSTF
    - ROMTbl[0][7]: E0043000, CID: B105900D, PID: 001BB961 TMC
    - ROMTbl[0][8]: E0044000, CID: B105F00D, PID: 001BB101 TSG
    - Executing init sequence ...
       - Initialized successfully
    - Target interface speed: 4000 kHz (Fixed)
    - CPU clock frequency: 47976 kHz (Auto detected)
    - J-Link found 1 JTAG device. Core ID: 0x5BA02477 (None)
    - Connected successfully
 - Checking if selected data fits into selected flash sectors.
 - Start of preparing flash programming
 - End of preparing flash programming
 - Start of determining dirty areas in flash cache
 - End of determining dirty areas
 - CPU is running at 47975 kHz.
 - Chip erase not supported for flash bank @ 0x00000000. Switched to sector erase
 - Start of determining dirty areas in flash cache
 - End of determining dirty areas
 - Start of erasing sectors
 - Blank checking 0x00000000 - 0x0001FFFF
 - Blank checking 0x00020000 - 0x0003FFFF
 - Blank checking 0x01010008 - 0x01010033
 - Blank checking 0x40100000 - 0x40101FFF
 - End of erasing sectors
 - Start of flash programming
 - Programming range 0x00000000 - 0x00007FFF ( 16 Sectors, 32 KB)
 - Programming range 0x00008000 - 0x0000FFFF ( 16 Sectors, 32 KB)
 - Programming range 0x00010000 - 0x000157FF ( 11 Sectors, 22 KB)
 - Programming range 0x40100000 - 0x401007FF (  2 Sectors, 2 KB)
 - End of flash programming
 - Flash programming performed for 2 ranges (90112 bytes)
 - 0x0000 - 0x157FF ( 43 Sectors, 86 KB)
 - 0x40100000 - 0x401007FF (  2 Sectors, 2 KB)
 - Start of verifying flash
 - End of verifying flash
 - Start of restoring
 - End of restoring
 - Executing exit sequence ...
    - De-initialized successfully
 - Target erased, programmed and verified successfully - Completed after 1.526 sec
 - Starting application ...
    - Disconnecting ...
       - Disconnected
    - Connecting via USB to J-Link device 0
    - J-Link firmware: J-Link / Flasher Portable Plus V1 compiled Feb 13 2020 16:15:24
    - Device "R7FS3A678" selected.
    - Found SW-DP with ID 0x5BA02477
    - Found SW-DP with ID 0x5BA02477
    - DPIDR: 0x5BA02477
    - Scanning AP map to find all available APs
    - AP[2]: Stopped AP scan as end of AP map has been reached
    - AP[0]: AHB-AP (IDR: 0x24770011)
    - AP[1]: APB-AP (IDR: 0x44770002)
    - Iterating through AP map to find AHB-AP to use
    - AP[0]: Core found
    - AP[0]: AHB-AP ROM base: 0xE00FF000
    - CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
    - Found Cortex-M4 r0p1, Little endian.
    - FPUnit: 6 code (BP) slots and 2 literal slots
    - CoreSight components:
    - ROMTbl[0] @ E00FF000
    - ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7
    - ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT
    - ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB
    - ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM
    - ROMTbl[0][4]: E0040000, CID: B105900D, PID: 000BB9A1 TPIU
    - ROMTbl[0][5]: E0041000, CID: B105900D, PID: 000BB925 ETM
    - ROMTbl[0][6]: E0042000, CID: B105900D, PID: 002BB908 CSTF
    - ROMTbl[0][7]: E0043000, CID: B105900D, PID: 001BB961 TMC
    - ROMTbl[0][8]: E0044000, CID: B105F00D, PID: 001BB101 TSG
    - Reset: Halt core after reset via DEMCR.VC_CORERESET.
    - Reset: Reset device via AIRCR.SYSRESETREQ.
    - Target application started



Reading entire flash chip ...
 - Connecting ...
    - Connecting via USB to J-Link device 0
    - J-Link firmware: J-Link / Flasher Portable Plus V1 compiled Feb 13 2020 16:15:24
    - Device "R7FS3A678" selected.
    - Target interface speed: 4000 kHz (Fixed)
    - VTarget = 3.295V
    - Found SW-DP with ID 0x5BA02477
    - Found SW-DP with ID 0x5BA02477
    - DPIDR: 0x5BA02477
    - Scanning AP map to find all available APs
    - AP[2]: Stopped AP scan as end of AP map has been reached
    - AP[0]: AHB-AP (IDR: 0x24770011)
    - AP[1]: APB-AP (IDR: 0x44770002)
    - Iterating through AP map to find AHB-AP to use
    - AP[0]: Core found
    - AP[0]: AHB-AP ROM base: 0xE00FF000
    - CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
    - Found Cortex-M4 r0p1, Little endian.
    - FPUnit: 6 code (BP) slots and 2 literal slots
    - CoreSight components:
    - ROMTbl[0] @ E00FF000
    - ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7
    - ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT
    - ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB
    - ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM
    - ROMTbl[0][4]: E0040000, CID: B105900D, PID: 000BB9A1 TPIU
    - ROMTbl[0][5]: E0041000, CID: B105900D, PID: 000BB925 ETM
    - ROMTbl[0][6]: E0042000, CID: B105900D, PID: 002BB908 CSTF
    - ROMTbl[0][7]: E0043000, CID: B105900D, PID: 001BB961 TMC
    - ROMTbl[0][8]: E0044000, CID: B105F00D, PID: 001BB101 TSG
    - Executing init sequence ...
       - Initialized successfully
    - Target interface speed: 4000 kHz (Fixed)
    - CPU clock frequency: 47978 kHz (Auto detected)
    - J-Link found 1 JTAG device. Core ID: 0x5BA02477 (None)
    - Connected successfully
 - 137 sectors, 3 ranges, 0x0 - 0x3FFFF, 0x1010008 - 0x1010033, 0x40100000 - 0x40101FFF
 - Start of preparing flash programming
 - End of preparing flash programming
 - Blank checking 0x00000000 - 0x0001FFFF
 - Blank checking 0x00020000 - 0x0003FFFF
 - Blank checking 0x01010008 - 0x01010033
 - Blank checking 0x40100000 - 0x40101FFF
 - Start of restoring
 - End of restoring
 - Target memory read successfully. (270380 bytes, 3 ranges) - Completed after 1.292 sec