Hi All,
My custom hardware is iMAX6Q processor based and similar to Nitrogen 6 max.
I'm referring to this link >> Debugging using Segger J-Link JTAG - Boundary Devices https://boundarydevices.com/debugging-using-segger-j-link-jtag/https://boundarydevices.com/debugging-using-segger-j-link-jtag/
1) In which boot mode we need to set the board when we are doing the kernel debug ? Do we need to load kernel via SD card ?
2) First I connected target hardware to JLink. Why it is showing No source available for 0x8ff532d4 ? Canyou see any mistake in following configurations. ?
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217463/1132-900/pastedImage_2.png[/img]
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217464/pastedImage_3.png[/img]
Next ran the Eclipse.
Debug configurations as follows.
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217465/pastedImage_4.png[/img]
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217466/pastedImage_5.png[/img]
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217467/pastedImage_6.png[/img]
Launch Group as follows.
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217468/pastedImage_7.png[/img]
When I hit Debug I got following results.
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217469/pastedImage_13.png[/img]
Here is the Console log. >> console log attached here with.
3) While running an application on linux in my custom hardware design I'm getting kernel panics. How can I debug this using JTAG ?
4) How can I give certain command to run an application on custom hardware and get information when it is crashing using JTAG ?
Could you please give me some idea regarding this ?
Regards,
Kulunu .
My custom hardware is iMAX6Q processor based and similar to Nitrogen 6 max.
I'm referring to this link >> Debugging using Segger J-Link JTAG - Boundary Devices https://boundarydevices.com/debugging-using-segger-j-link-jtag/https://boundarydevices.com/debugging-using-segger-j-link-jtag/
1) In which boot mode we need to set the board when we are doing the kernel debug ? Do we need to load kernel via SD card ?
2) First I connected target hardware to JLink. Why it is showing No source available for 0x8ff532d4 ? Canyou see any mistake in following configurations. ?
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217463/1132-900/pastedImage_2.png[/img]
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217464/pastedImage_3.png[/img]
Next ran the Eclipse.
Debug configurations as follows.
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217465/pastedImage_4.png[/img]
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217466/pastedImage_5.png[/img]
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217467/pastedImage_6.png[/img]
Launch Group as follows.
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217468/pastedImage_7.png[/img]
When I hit Debug I got following results.
[img]https://community.nxp.com/servlet/JiveServlet/downloadImage/2-1007817-217469/pastedImage_13.png[/img]
Here is the Console log. >> console log attached here with.
3) While running an application on linux in my custom hardware design I'm getting kernel panics. How can I debug this using JTAG ?
4) How can I give certain command to run an application on custom hardware and get information when it is crashing using JTAG ?
Could you please give me some idea regarding this ?
Regards,
Kulunu .