Hi, i have a LPC1114F/302 based board(footnote 1). I was initially trying to control a GPIO pin, without success. And when i checked the registers, they where all filled with junk, even if i reset the target, the values of the regs stay. Now i am simple trying to put a value into r0: MOV r0, #5 . Though when i download the code nothing happens. My OS is linux mint 17.1 64bit, and im using the fasmarm assembler.
Here is my procedure:

$ sudo JLinkExe
[sudo] password for josef:
SEGGER J-Link Commander V4.98e ('?' for help)
Compiled May 5 2015 11:49:39
DLL version V4.98e, compiled May 5 2015 11:49:35
Firmware: J-Link V9 compiled Apr 21 2015 18:10:40
Hardware: V9.30
S/N: *************
OEM: SEGGER-EDU
Feature(s): FlashBP, GDB
VTarget = 0.000V
J-Link>power on
J-Link>si 1
Selecting SWD as current target interface.
Setting target interface speed to 1MHz. Use "Speed" to change.
J-Link>le
J-Link>device LPC1114/302
Info: Device "LPC1114/302" selected.
Reconnecting to target...
Info: Found SWD-DP with ID 0x0BB11477
Info: Found Cortex-M0 r0p0, Little endian.
Info: FPUnit: 4 code (BP) slots and 0 literal slots
Info: CoreSight components:
Info: ROMTbl 0 @ E00FF000
Info: ROMTbl 0 [0]: FFF0F000, CID: B105E00D, PID: 000BB008 SCS
Info: ROMTbl 0 [1]: FFF02000, CID: B105E00D, PID: 000BB00A DWT
Info: ROMTbl 0 [2]: FFF03000, CID: B105E00D, PID: 000BB00B FPB
J-Link>loadbin test.bin, 0x00
Downloading file [test.bin]...O.K.
J-Link>regs
PC = FFFFFFFE, CycleCnt = 00000000
R0 = 00000000, R1 = 60010108, R2 = 00000000, R3 = 00000000
R4 = 40048000, R5 = 7C5ABECB, R6 = 40048000, R7 = 400483C0
R8 = C89B2B30, R9 = 3416ABC0, R10= 1CF55939, R11= 5FEA6B36
R12= 9631F8EE
SP(R13)= E39FFFE0, MSP= E39FFFE0, PSP= AB11EDC0, R14(LR) = FFFFFFF9
XPSR = 61000003: APSR = nZCvq, EPSR = 01000000, IPSR = 003 (HardFault)
CFBP = 00000000, CONTROL = 00, FAULTMASK = 00, BASEPRI = 00, PRIMASK = 00
J-Link>r
Reset delay: 0 ms
Reset type NORMAL: Resets core & peripherals via SYSRESETREQ & VECTRESET bit.
J-Link>regs
PC = 1FFF10EA, CycleCnt = 00000000
R0 = 00000000, R1 = 00000001, R2 = E3A00005, R3 = 00000000
R4 = 40048000, R5 = 60010108, R6 = 40048000, R7 = 400483C0
R8 = C89B2B30, R9 = 3416ABC0, R10= 1CF55939, R11= 5FEA6B36
R12= 9631F8EE
SP(R13)= 10001FA8, MSP= 10001FA8, PSP= AB11EDC0, R14(LR) = 1FFF1109
XPSR = 01000000: APSR = nzcvq, EPSR = 01000000, IPSR = 000 (NoException)
CFBP = 00000000, CONTROL = 00, FAULTMASK = 00, BASEPRI = 00, PRIMASK = 00
J-Link>

(nothing changes after reset)


Thanks for responses and suggestions!

1: olimex.com/Products/ARM/NXP/LPC-H1114/

I fixed the problem! I seems i was using the JLinkExe program wrong. The solution was to first specify SWD, little endian and device(as before). And then halt the processor. Clear the regs manually. Set programcounter to zero. Load program with loadbin. then run the program with 'go'. Now the results are as expected.